RE: [PATCH 1/2] dt-bindings: net: bluetooth: nxp: add support for supply and reset

From: Sherry Sun
Date: Sun Oct 06 2024 - 04:49:25 EST




> -----Original Message-----
> From: Catalin Popescu <catalin.popescu@xxxxxxxxxxxxxxxxxxxx>
> Sent: Friday, October 4, 2024 7:36 PM
> To: Amitkumar Karwar <amitkumar.karwar@xxxxxxx>; Neeraj Sanjay Kale
> <neeraj.sanjaykale@xxxxxxx>; marcel@xxxxxxxxxxxx;
> luiz.dentz@xxxxxxxxx; robh@xxxxxxxxxx; krzk+dt@xxxxxxxxxx;
> conor+dt@xxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx
> Cc: linux-bluetooth@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; m.felsch@xxxxxxxxxxxxxx; bsp-
> development.geo@xxxxxxxxxxxxxxxxxxxx; Catalin Popescu
> <catalin.popescu@xxxxxxxxxxxxxxxxxxxx>
> Subject: [PATCH 1/2] dt-bindings: net: bluetooth: nxp: add support for supply
> and reset
>
> Add support for chip power supply and chip reset/powerdown.
>
> Signed-off-by: Catalin Popescu <catalin.popescu@xxxxxxxxxxxxxxxxxxxx>
> ---
> .../bindings/net/bluetooth/nxp,88w8987-bt.yaml | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-
> bt.yaml b/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-
> bt.yaml
> index 37a65badb448..8520b3812bd2 100644
> --- a/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-
> bt.yaml
> +++ b/Documentation/devicetree/bindings/net/bluetooth/nxp,88w8987-
> bt.yaml
> @@ -34,6 +34,14 @@ properties:
> firmware-name:
> maxItems: 1
>
> + vcc-supply:
> + description:
> + phandle of the regulator that provides the supply voltage.
> +
> + reset-gpios:
> + description:
> + Chip powerdown/reset signal (PDn).
> +

Hi Catalin,

For NXP WIFI/BT chip, WIFI and BT share the one PDn pin, which means that both wifi and BT controller will be powered on and off at the same time.
Taking the M.2 NXP WIFI/BT module as an example, pin56(W_DISABLE1) is connected to the WIFI/BT chip PDn pin, we has already controlled this pin in the corresponding PCIe/SDIO controller dts nodes.
It is not clear to me what exactly pins for vcc-supply and reset-gpios you describing here. Can you help understand the corresponding pins on M.2 interface as an example? Thanks.

Best Regards
Sherry


> required:
> - compatible
>
> @@ -41,10 +49,13 @@ additionalProperties: false
>
> examples:
> - |
> + #include <dt-bindings/gpio/gpio.h>
> serial {
> bluetooth {
> compatible = "nxp,88w8987-bt";
> fw-init-baudrate = <3000000>;
> firmware-name = "uartuart8987_bt_v0.bin";
> + vcc-supply = <&nxp_iw612_supply>;
> + reset-gpios = <&gpioctrl 2 GPIO_ACTIVE_LOW>;
> };
> };
> --
> 2.34.1
>