[PATCH 2/3] arm64: dts: qcom: x1e80100: Add uart14

[Stephan Gerhold]

Add the uart14 instance for X1E80100 (typically used for Bluetooth).

Signed-off-by: Stephan Gerhold <stephan.gerhold@xxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/x1e80100.dtsi | 53 ++++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
index 06d27c65dc11..185bb15c2945 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
@@ -1991,6 +1991,31 @@ &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>,
 				status = "disabled";
 			};
 
+			uart14: serial@a98000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a98000 0 0x4000>;
+
+				interrupts = <GIC_SPI 806 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				power-domains = <&rpmhpd RPMHPD_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+
+				pinctrl-0 = <&qup_uart14_default>;
+				pinctrl-names = "default";
+
+				status = "disabled";
+			};
+
 			i2c15: i2c@a9c000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0 0x00a9c000 0 0x4000>;
@@ -5802,6 +5827,34 @@ rx-pins {
 				};
 			};
 
+			qup_uart14_default: qup-uart14-default-state {
+				cts-pins {
+					pins = "gpio56";
+					function = "qup1_se6";
+					bias-bus-hold;
+				};
+
+				rts-pins {
+					pins = "gpio57";
+					function = "qup1_se6";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				tx-pins {
+					pins = "gpio58";
+					function = "qup1_se6";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-pins {
+					pins = "gpio59";
+					function = "qup1_se6";
+					bias-pull-up;
+				};
+			};
+
 			qup_uart21_default: qup-uart21-default-state {
 				tx-pins {
 					pins = "gpio86";

-- 
2.46.0