[PATCH v1] arm64: dts: qcom: qcs8300: Add QUPv3 configuration
From: Viken Dadhaniya
Date: Wed Oct 09 2024 - 05:12:39 EST
Add DT support for QUPV3 Serial Engines.
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@xxxxxxxxxxx>
---
Build Dependencies:
Base Link:
https://lore.kernel.org/linux-arm-msm/20240904-qcs8300_initial_dtsi-v1-18-d0ea9afdc007@xxxxxxxxxxx/
https://lore.kernel.org/all/202409080715.rGuyyNu2-lkp@xxxxxxxxx/T/
GCC Link: https://lore.kernel.org/all/20240820-qcs8300-gcc-v1-0-d81720517a82@xxxxxxxxxxx/
ICC Link: https://lore.kernel.org/linux-arm-msm/20240906151534.6418-2-quic_rlaggysh@xxxxxxxxxxx/
---
arch/arm64/boot/dts/qcom/qcs8300.dtsi | 2077 +++++++++++++++++++++++--
1 file changed, 1932 insertions(+), 145 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
index 2c35f96c3f28..ab9c9dc61a4f 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
@@ -5,6 +5,7 @@
#include <dt-bindings/clock/qcom,qcs8300-gcc.h>
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/interconnect/qcom,icc.h>
#include <dt-bindings/interconnect/qcom,qcs8300-rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -18,6 +19,39 @@
#address-cells = <2>;
#size-cells = <2>;
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ i2c8 = &i2c8;
+ i2c9 = &i2c9;
+ i2c10 = &i2c10;
+ i2c11 = &i2c11;
+ i2c12 = &i2c12;
+ i2c13 = &i2c13;
+ i2c14 = &i2c14;
+ i2c15 = &i2c15;
+ spi0 = &spi0;
+ spi1 = &spi1;
+ spi2 = &spi2;
+ spi3 = &spi3;
+ spi4 = &spi4;
+ spi5 = &spi5;
+ spi6 = &spi6;
+ spi8 = &spi8;
+ spi9 = &spi9;
+ spi10 = &spi10;
+ spi12 = &spi12;
+ spi13 = &spi13;
+ spi14 = &spi14;
+ spi15 = &spi15;
+ serial0 = &uart7;
+ };
+
cpus {
#address-cells = <2>;
#size-cells = <0>;
@@ -372,6 +406,15 @@
};
};
+ qup_opp_table: opp-table-qup {
+ compatible = "operating-points-v2";
+
+ opp-120000000 {
+ opp-hz = /bits/ 64 <120000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
@@ -558,6 +601,29 @@
#size-cells = <1>;
};
+ gpi_dma0: qcom,gpi-dma@900000 {
+ compatible = "qcom,sm6350-gpi-dma";
+ #dma-cells = <3>;
+ reg = <0x0 0x900000 0x0 0x60000>;
+ interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x416 0x0>;
+ dma-channels = <12>;
+ dma-channel-mask = <0xfff>;
+ dma-coherent;
+ status = "disabled";
+ };
+
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x9c0000 0x0 0x2000>;
@@ -568,175 +634,1277 @@
"s-ahb";
#address-cells = <2>;
#size-cells = <2>;
+ iommus = <&apps_smmu 0x403 0x0>;
+ dma-coherent;
status = "disabled";
- uart7: serial@99c000 {
- compatible = "qcom,geni-debug-uart";
- reg = <0x0 0x0099c000 0x0 0x4000>;
- clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ i2c0: i2c@980000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x980000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
clock-names = "se";
- pinctrl-0 = <&qup_uart7_default>;
+ pinctrl-0 = <&qup_i2c0_data_clk>;
pinctrl-names = "default";
- interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
- interconnects = <&clk_virt MASTER_QUP_CORE_0 0
- &clk_virt SLAVE_QUP_CORE_0 0>,
- <&gem_noc MASTER_APPSS_PROC 0
- &config_noc SLAVE_QUP_0 0>;
+ interrupts = <GIC_SPI 550 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "qup-core",
- "qup-config";
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
status = "disabled";
};
- };
- config_noc: interconnect@14c0000 {
- compatible = "qcom,qcs8300-config-noc";
- reg = <0x0 0x014c0000 0x0 0x13080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ spi0: spi@980000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x980000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 550 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- system_noc: interconnect@1680000 {
- compatible = "qcom,qcs8300-system-noc";
- reg = <0x0 0x01680000 0x0 0x15080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ uart0: serial@980000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x980000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>,
+ <&qup_uart0_tx>, <&qup_uart0_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 550 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- aggre1_noc: interconnect@16c0000 {
- compatible = "qcom,qcs8300-aggre1-noc";
- reg = <0x0 0x016c0000 0x0 0x17080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ i2c1: i2c@984000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x984000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c1_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 551 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- aggre2_noc: interconnect@1700000 {
- compatible = "qcom,qcs8300-aggre2-noc";
- reg = <0x0 0x01700000 0x0 0x1a080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ spi1: spi@984000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x984000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 551 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- pcie_anoc: interconnect@1760000 {
- compatible = "qcom,qcs8300-pcie-anoc";
- reg = <0x0 0x01760000 0x0 0xc080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ uart1: serial@984000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x984000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>,
+ <&qup_uart1_tx>, <&qup_uart1_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 551 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- gpdsp_anoc: interconnect@1780000 {
- compatible = "qcom,qcs8300-gpdsp-anoc";
- reg = <0x0 0x01780000 0x0 0xd080>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ i2c2: i2c@988000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x988000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c2_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- mmss_noc: interconnect@17a0000 {
- compatible = "qcom,qcs8300-mmss-noc";
- reg = <0x0 0x017a0000 0x0 0x40000>;
- #interconnect-cells = <2>;
- qcom,bcm-voters = <&apps_bcm_voter>;
- };
+ spi2: spi@988000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x988000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- ufs_mem_hc: ufs@1d84000 {
- compatible = "qcom,qcs8300-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
- reg = <0x0 0x01d84000 0x0 0x3000>;
- interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
- phys = <&ufs_mem_phy>;
- phy-names = "ufsphy";
- lanes-per-direction = <2>;
- #reset-cells = <1>;
- resets = <&gcc GCC_UFS_PHY_BCR>;
- reset-names = "rst";
+ uart2: serial@988000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x988000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>,
+ <&qup_uart2_tx>, <&qup_uart2_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 529 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- power-domains = <&gcc GCC_UFS_PHY_GDSC>;
- required-opps = <&rpmhpd_opp_nom>;
+ i2c3: i2c@98c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x98c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c3_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- iommus = <&apps_smmu 0x100 0x0>;
- dma-coherent;
+ spi3: spi@98c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x98c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- interconnects = <&aggre1_noc MASTER_UFS_MEM 0
- &mc_virt SLAVE_EBI1 0>,
- <&gem_noc MASTER_APPSS_PROC 0
- &config_noc SLAVE_UFS_MEM_CFG 0>;
- interconnect-names = "ufs-ddr",
- "cpu-ufs";
+ uart3: serial@98c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x98c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>,
+ <&qup_uart3_tx>, <&qup_uart3_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
- <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
- <&gcc GCC_UFS_PHY_AHB_CLK>,
- <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
- <&rpmhcc RPMH_CXO_CLK>,
- <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
- <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
- <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
- clock-names = "core_clk",
- "bus_aggr_clk",
- "iface_clk",
- "core_clk_unipro",
- "ref_clk",
- "tx_lane0_sync_clk",
- "rx_lane0_sync_clk",
- "rx_lane1_sync_clk";
- freq-table-hz = <75000000 300000000>,
- <0 0>,
- <0 0>,
- <75000000 300000000>,
- <0 0>,
- <0 0>,
- <0 0>,
- <0 0>;
- status = "disabled";
- };
+ i2c4: i2c@990000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x990000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c4_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- ufs_mem_phy: phy@1d87000 {
- compatible = "qcom,qcs8300-qmp-ufs-phy", "qcom,sa8775p-qmp-ufs-phy";
- reg = <0x0 0x01d87000 0x0 0xe10>;
- /*
- * Yes, GCC_EDP_REF_CLKREF_EN is correct in qref. It
- * enables the CXO clock to eDP *and* UFS PHY.
- */
- clocks = <&rpmhcc RPMH_CXO_CLK>,
- <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
- <&gcc GCC_EDP_REF_CLKREF_EN>;
- clock-names = "ref",
- "ref_aux",
- "qref";
- power-domains = <&gcc GCC_UFS_PHY_GDSC>;
+ spi4: spi@990000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x990000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- resets = <&ufs_mem_hc 0>;
- reset-names = "ufsphy";
+ uart4: serial@990000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x990000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>,
+ <&qup_uart4_tx>, <&qup_uart4_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 531 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- #phy-cells = <0>;
- status = "disabled";
- };
+ i2c5: i2c@994000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x994000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c5_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 535 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- tcsr_mutex: hwlock@1f40000 {
- compatible = "qcom,tcsr-mutex";
- reg = <0x0 0x01f40000 0x0 0x20000>;
- #hwlock-cells = <1>;
- };
+ spi5: spi@994000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x994000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 535 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- tcsr: syscon@1fc0000 {
- compatible = "qcom,qcs8300-tcsr", "syscon";
- reg = <0x0 0x1fc0000 0x0 0x30000>;
- };
+ uart5: serial@994000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x994000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>,
+ <&qup_uart5_tx>, <&qup_uart5_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 535 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
- remoteproc_adsp: remoteproc@3000000 {
- compatible = "qcom,qcs8300-adsp-pas", "qcom,sa8775p-adsp-pas";
- reg = <0x0 0x3000000 0x0 0x00100>;
+ i2c6: i2c@998000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c6_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+ <&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
- <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
- interrupt-names = "wdog",
- "fatal",
- "ready",
- "handover",
- "stop-ack";
+ spi6: spi@998000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
- clocks = <&rpmhcc RPMH_CXO_CLK>;
+ uart6: serial@998000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0x998000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>,
+ <&qup_uart6_tx>, <&qup_uart6_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ uart7: serial@99c000 {
+ compatible = "qcom,geni-debug-uart";
+ reg = <0x0 0x0099c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+ };
+
+ gpi_dma1: qcom,gpi-dma@a00000 {
+ compatible = "qcom,sm6350-gpi-dma";
+ reg = <0x0 0xa00000 0x0 0x60000>;
+ #dma-cells = <3>;
+ interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x456 0x0>;
+ dma-channels = <12>;
+ dma-channel-mask = <0xfff>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ qupv3_id_1: geniqup@ac0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0xac0000 0x0 0x2000>;
+ ranges;
+ clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+ clock-names = "m-ahb",
+ "s-ahb";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ iommus = <&apps_smmu 0x443 0x0>;
+ dma-coherent;
+ status = "disabled";
+
+ i2c8: i2c@a80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c8_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi8: spi@a80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart8: serial@a80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>,
+ <&qup_uart8_tx>, <&qup_uart8_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c9: i2c@a84000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa84000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c9_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi9: spi@a84000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa84000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart9: serial@a84000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa84000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>,
+ <&qup_uart9_tx>, <&qup_uart9_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c10: i2c@a88000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa88000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c10_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi10: spi@a88000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa88000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart10: serial@a88000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa88000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>,
+ <&qup_uart10_tx>, <&qup_uart10_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c11: i2c@a8c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa8c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c11_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart11: serial@a8c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa8c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart11_tx>, <&qup_uart11_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c12: i2c@a90000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa90000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi12: spi@a90000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa90000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart12: serial@a90000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa90000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>,
+ <&qup_uart12_tx>, <&qup_uart12_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c13: i2c@a94000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c13_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi13: spi@a94000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart13: serial@a94000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa94000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>,
+ <&qup_uart13_tx>, <&qup_uart13_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c14: i2c@a98000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa98000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c14_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi14: spi@a98000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa98000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart14: serial@a98000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa98000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>,
+ <&qup_uart14_tx>, <&qup_uart14_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+
+ i2c15: i2c@a9c000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xa9c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c15_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+ <&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+ <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi15: spi@a9c000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xa9c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
+ <&gpi_dma1 1 7 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart15: serial@a9c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xa9c000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>,
+ <&qup_uart15_tx>, <&qup_uart15_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+ };
+
+ gpi_dma3: qcom,gpi-dma@b00000 {
+ compatible = "qcom,sm6350-gpi-dma";
+ reg = <0x0 0xb00000 0x0 0x60000>;
+ #dma-cells = <3>;
+ interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 527 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 528 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&apps_smmu 0x56 0x0>;
+ dma-channels = <4>;
+ dma-channel-mask = <0xf>;
+ dma-coherent;
+ status = "disabled";
+ };
+
+ qupv3_id_3: geniqup@bc0000 {
+ compatible = "qcom,geni-se-qup";
+ reg = <0x0 0xbc0000 0x0 0x2000>;
+ ranges;
+ clocks = <&gcc GCC_QUPV3_WRAP_3_M_AHB_CLK>,
+ <&gcc GCC_QUPV3_WRAP_3_S_AHB_CLK>;
+ clock-names = "m-ahb",
+ "s-ahb";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ iommus = <&apps_smmu 0x43 0x0>;
+ dma-coherent;
+ status = "disabled";
+
+ i2c16: i2c@b80000 {
+ compatible = "qcom,geni-i2c";
+ reg = <0x0 0xb80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP3_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_i2c16_data_clk>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 830 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_3 0 &clk_virt SLAVE_QUP_CORE_3 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_3 0>,
+ <&aggre2_noc MASTER_QUP_3 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "qup-core",
+ "qup-config",
+ "qup-memory";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ dmas = <&gpi_dma3 0 0 QCOM_GPI_I2C>,
+ <&gpi_dma3 1 0 QCOM_GPI_I2C>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ spi16: spi@b80000 {
+ compatible = "qcom,geni-spi";
+ reg = <0x0 0xb80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP3_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 830 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_3 0 &clk_virt SLAVE_QUP_CORE_3 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_3 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ dmas = <&gpi_dma3 0 0 QCOM_GPI_SPI>,
+ <&gpi_dma3 1 0 QCOM_GPI_SPI>;
+ dma-names = "tx",
+ "rx";
+ status = "disabled";
+ };
+
+ uart16: serial@b80000 {
+ compatible = "qcom,geni-uart";
+ reg = <0x0 0xb80000 0x0 0x4000>;
+ clocks = <&gcc GCC_QUPV3_WRAP3_S0_CLK>;
+ clock-names = "se";
+ pinctrl-0 = <&qup_uart16_cts>, <&qup_uart16_rts>,
+ <&qup_uart16_tx>, <&qup_uart16_rx>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 830 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_3 0 &clk_virt SLAVE_QUP_CORE_3 0>,
+ <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_3 0>;
+ interconnect-names = "qup-core",
+ "qup-config";
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&qup_opp_table>;
+ status = "disabled";
+ };
+ };
+
+ config_noc: interconnect@14c0000 {
+ compatible = "qcom,qcs8300-config-noc";
+ reg = <0x0 0x014c0000 0x0 0x13080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ system_noc: interconnect@1680000 {
+ compatible = "qcom,qcs8300-system-noc";
+ reg = <0x0 0x01680000 0x0 0x15080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre1_noc: interconnect@16c0000 {
+ compatible = "qcom,qcs8300-aggre1-noc";
+ reg = <0x0 0x016c0000 0x0 0x17080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre2_noc: interconnect@1700000 {
+ compatible = "qcom,qcs8300-aggre2-noc";
+ reg = <0x0 0x01700000 0x0 0x1a080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ pcie_anoc: interconnect@1760000 {
+ compatible = "qcom,qcs8300-pcie-anoc";
+ reg = <0x0 0x01760000 0x0 0xc080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ gpdsp_anoc: interconnect@1780000 {
+ compatible = "qcom,qcs8300-gpdsp-anoc";
+ reg = <0x0 0x01780000 0x0 0xd080>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mmss_noc: interconnect@17a0000 {
+ compatible = "qcom,qcs8300-mmss-noc";
+ reg = <0x0 0x017a0000 0x0 0x40000>;
+ #interconnect-cells = <2>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ ufs_mem_hc: ufs@1d84000 {
+ compatible = "qcom,qcs8300-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
+ reg = <0x0 0x01d84000 0x0 0x3000>;
+ interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&ufs_mem_phy>;
+ phy-names = "ufsphy";
+ lanes-per-direction = <2>;
+ #reset-cells = <1>;
+ resets = <&gcc GCC_UFS_PHY_BCR>;
+ reset-names = "rst";
+
+ power-domains = <&gcc GCC_UFS_PHY_GDSC>;
+ required-opps = <&rpmhpd_opp_nom>;
+
+ iommus = <&apps_smmu 0x100 0x0>;
+ dma-coherent;
+
+ interconnects = <&aggre1_noc MASTER_UFS_MEM 0
+ &mc_virt SLAVE_EBI1 0>,
+ <&gem_noc MASTER_APPSS_PROC 0
+ &config_noc SLAVE_UFS_MEM_CFG 0>;
+ interconnect-names = "ufs-ddr",
+ "cpu-ufs";
+
+ clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+ <&gcc GCC_UFS_PHY_AHB_CLK>,
+ <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+ <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+ clock-names = "core_clk",
+ "bus_aggr_clk",
+ "iface_clk",
+ "core_clk_unipro",
+ "ref_clk",
+ "tx_lane0_sync_clk",
+ "rx_lane0_sync_clk",
+ "rx_lane1_sync_clk";
+ freq-table-hz = <75000000 300000000>,
+ <0 0>,
+ <0 0>,
+ <75000000 300000000>,
+ <0 0>,
+ <0 0>,
+ <0 0>,
+ <0 0>;
+ status = "disabled";
+ };
+
+ ufs_mem_phy: phy@1d87000 {
+ compatible = "qcom,qcs8300-qmp-ufs-phy", "qcom,sa8775p-qmp-ufs-phy";
+ reg = <0x0 0x01d87000 0x0 0xe10>;
+ /*
+ * Yes, GCC_EDP_REF_CLKREF_EN is correct in qref. It
+ * enables the CXO clock to eDP *and* UFS PHY.
+ */
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+ <&gcc GCC_EDP_REF_CLKREF_EN>;
+ clock-names = "ref",
+ "ref_aux",
+ "qref";
+ power-domains = <&gcc GCC_UFS_PHY_GDSC>;
+
+ resets = <&ufs_mem_hc 0>;
+ reset-names = "ufsphy";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ tcsr_mutex: hwlock@1f40000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x0 0x01f40000 0x0 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tcsr: syscon@1fc0000 {
+ compatible = "qcom,qcs8300-tcsr", "syscon";
+ reg = <0x0 0x1fc0000 0x0 0x30000>;
+ };
+
+ remoteproc_adsp: remoteproc@3000000 {
+ compatible = "qcom,qcs8300-adsp-pas", "qcom,sa8775p-adsp-pas";
+ reg = <0x0 0x3000000 0x0 0x00100>;
+
+ interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog",
+ "fatal",
+ "ready",
+ "handover",
+ "stop-ack";
+
+ clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd RPMHPD_LCX>,
@@ -950,11 +2118,630 @@
#interrupt-cells = <2>;
wakeup-parent = <&pdc>;
- qup_uart7_default: qup-uart7-state {
- /* TX, RX */
- pins = "gpio43", "gpio44";
+ qup_i2c0_data_clk: qup-i2c0-data-clk-state {
+ pins = "gpio17", "gpio18";
+ function = "qup0_se0";
+ };
+
+ qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+ pins = "gpio19", "gpio20";
+ function = "qup0_se1";
+ };
+
+ qup_i2c2_data_clk: qup-i2c2-data-clk-state {
+ pins = "gpio33", "gpio34";
+ function = "qup0_se2";
+ };
+
+ qup_i2c3_data_clk: qup-i2c3-data-clk-state {
+ pins = "gpio25", "gpio26";
+ function = "qup0_se3";
+ };
+
+ qup_i2c4_data_clk: qup-i2c4-data-clk-state {
+ pins = "gpio29", "gpio30";
+ function = "qup0_se4";
+ };
+
+ qup_i2c5_data_clk: qup-i2c5-data-clk-state {
+ pins = "gpio21", "gpio22";
+ function = "qup0_se5";
+ };
+
+ qup_i2c6_data_clk: qup-i2c6-data-clk-state {
+ pins = "gpio80", "gpio81";
+ function = "qup0_se6";
+ };
+
+ qup_i2c8_data_clk: qup-i2c8-data-clk-state {
+ pins = "gpio37", "gpio38";
+ function = "qup1_se0";
+ };
+
+ qup_i2c9_data_clk: qup-i2c9-data-clk-state {
+ pins = "gpio39", "gpio40";
+ function = "qup1_se1";
+ };
+
+ qup_i2c10_data_clk: qup-i2c10-data-clk-state {
+ pins = "gpio84", "gpio85";
+ function = "qup1_se2";
+ };
+
+ qup_i2c11_data_clk: qup-i2c11-data-clk-state {
+ pins = "gpio41", "gpio42";
+ function = "qup1_se3";
+ };
+
+ qup_i2c12_data_clk: qup-i2c12-data-clk-state {
+ pins = "gpio45", "gpio46";
+ function = "qup1_se4";
+ };
+
+ qup_i2c13_data_clk: qup-i2c13-data-clk-state {
+ pins = "gpio49", "gpio50";
+ function = "qup1_se5";
+ };
+
+ qup_i2c14_data_clk: qup-i2c14-data-clk-state {
+ pins = "gpio89", "gpio90";
+ function = "qup1_se6";
+ };
+
+ qup_i2c15_data_clk: qup-i2c15-data-clk-state {
+ pins = "gpio91", "gpio92";
+ function = "qup1_se7";
+ };
+
+ qup_i2c16_data_clk: qup-i2c16-data-clk-state {
+ pins = "gpio10", "gpio11";
+ function = "qup2_se0";
+ };
+
+ qup_spi0_data_clk: qup-spi0-data-clk-state {
+ pins = "gpio17", "gpio18", "gpio19";
+ function = "qup0_se0";
+ };
+
+ qup_spi0_cs: qup-spi0-cs-state {
+ pins = "gpio20";
+ function = "qup0_se0";
+ };
+
+ qup_spi0_cs_gpio: qup-spi0-cs-gpio-state {
+ pins = "gpio20";
+ function = "gpio";
+ };
+
+ qup_spi1_data_clk: qup-spi1-data-clk-state {
+ pins = "gpio19", "gpio20", "gpio17";
+ function = "qup0_se1";
+ };
+
+ qup_spi1_cs: qup-spi1-cs-state {
+ pins = "gpio18";
+ function = "qup0_se1";
+ };
+
+ qup_spi1_cs_gpio: qup-spi1-cs-gpio-state {
+ pins = "gpio18";
+ function = "gpio";
+ };
+
+ qup_spi2_data_clk: qup-spi2-data-clk-state {
+ pins = "gpio33", "gpio34", "gpio35";
+ function = "qup0_se2";
+ };
+
+ qup_spi2_cs: qup-spi2-cs-state {
+ pins = "gpio36";
+ function = "qup0_se2";
+ };
+
+ qup_spi2_cs_gpio: qup-spi2-cs-gpio-state {
+ pins = "gpio36";
+ function = "gpio";
+ };
+
+ qup_spi3_data_clk: qup-spi3-data-clk-state {
+ pins = "gpio25", "gpio26", "gpio27";
+ function = "qup0_se3";
+ };
+
+ qup_spi3_cs: qup-spi3-cs-state {
+ pins = "gpio28";
+ function = "qup0_se3";
+ };
+
+ qup_spi3_cs_gpio: qup-spi3-cs-gpio-state {
+ pins = "gpio28";
+ function = "gpio";
+ };
+
+ qup_spi4_data_clk: qup-spi4-data-clk-state {
+ pins = "gpio29", "gpio30", "gpio31";
+ function = "qup0_se4";
+ };
+
+ qup_spi4_cs: qup-spi4-cs-state {
+ pins = "gpio32";
+ function = "qup0_se4";
+ };
+
+ qup_spi4_cs_gpio: qup-spi4-cs-gpio-state {
+ pins = "gpio32";
+ function = "gpio";
+ };
+
+ qup_spi5_data_clk: qup-spi5-data-clk-state {
+ pins = "gpio21", "gpio22", "gpio23";
+ function = "qup0_se5";
+ };
+
+ qup_spi5_cs: qup-spi5-cs-state {
+ pins = "gpio24";
+ function = "qup0_se5";
+ };
+
+ qup_spi5_cs_gpio: qup-spi5-cs-gpio-state {
+ pins = "gpio24";
+ function = "gpio";
+ };
+
+ qup_spi6_data_clk: qup-spi6-data-clk-state {
+ pins = "gpio80", "gpio81", "gpio82";
+ function = "qup0_se6";
+ };
+
+ qup_spi6_cs: qup-spi6-cs-state {
+ pins = "gpio83";
+ function = "qup0_se6";
+ };
+
+ qup_spi6_cs_gpio: qup-spi6-cs-gpio-state {
+ pins = "gpio83";
+ function = "gpio";
+ };
+
+ qup_spi8_data_clk: qup-spi8-data-clk-state {
+ pins = "gpio37", "gpio38", "gpio39";
+ function = "qup1_se0";
+ };
+
+ qup_spi8_cs: qup-spi8-cs-state {
+ pins = "gpio40";
+ function = "qup1_se0";
+ };
+
+ qup_spi8_cs_gpio: qup-spi8-cs-gpio-state {
+ pins = "gpio40";
+ function = "gpio";
+ };
+
+ qup_spi9_data_clk: qup-spi9-data-clk-state {
+ pins = "gpio39", "gpio40", "gpio37";
+ function = "qup1_se1";
+ };
+
+ qup_spi9_cs: qup-spi9-cs-state {
+ pins = "gpio38";
+ function = "qup1_se1";
+ };
+
+ qup_spi9_cs_gpio: qup-spi9-cs-gpio-state {
+ pins = "gpio38";
+ function = "gpio";
+ };
+
+ qup_spi10_data_clk: qup-spi10-data-clk-state {
+ pins = "gpio84", "gpio85", "gpio86";
+ function = "qup1_se2";
+ };
+
+ qup_spi10_cs: qup-spi10-cs-state {
+ pins = "gpio87";
+ function = "qup1_se2";
+ };
+
+ qup_spi10_cs_gpio: qup-spi10-cs-gpio-state {
+ pins = "gpio87";
+ function = "gpio";
+ };
+
+ qup_spi12_data_clk: qup-spi12-data-clk-state {
+ pins = "gpio45", "gpio46", "gpio47";
+ function = "qup1_se4";
+ };
+
+ qup_spi12_cs: qup-spi12-cs-state {
+ pins = "gpio48";
+ function = "qup1_se4";
+ };
+
+ qup_spi12_cs_gpio: qup-spi12-cs-gpio-state {
+ pins = "gpio48";
+ function = "gpio";
+ };
+
+ qup_spi13_data_clk: qup-spi13-data-clk-state {
+ pins = "gpio49", "gpio50", "gpio51";
+ function = "qup1_se5";
+ };
+
+ qup_spi13_cs: qup-spi13-cs-state {
+ pins = "gpio52";
+ function = "qup1_se5";
+ };
+
+ qup_spi13_cs_gpio: qup-spi13-cs-gpio-state {
+ pins = "gpio52";
+ function = "gpio";
+ };
+
+ qup_spi14_data_clk: qup-spi14-data-clk-state {
+ pins = "gpio89", "gpio90", "gpio91";
+ function = "qup1_se6";
+ };
+
+ qup_spi14_cs: qup-spi14-cs-state {
+ pins = "gpio92";
+ function = "qup1_se6";
+ };
+
+ qup_spi14_cs_gpio: qup-spi14-cs-gpio-state {
+ pins = "gpio92";
+ function = "gpio";
+ };
+
+ qup_spi15_data_clk: qup-spi15-data-clk-state {
+ pins = "gpio91", "gpio92", "gpio89";
+ function = "qup1_se7";
+ };
+
+ qup_spi15_cs: qup-spi15-cs-state {
+ pins = "gpio90";
+ function = "qup1_se7";
+ };
+
+ qup_spi15_cs_gpio: qup-spi15-cs-gpio-state {
+ pins = "gpio90";
+ function = "gpio";
+ };
+
+ qup_spi16_data_clk: qup-spi16-data-clk-state {
+ pins = "gpio10", "gpio11", "gpio12";
+ function = "qup2_se0";
+ };
+
+ qup_spi16_cs: qup-spi16-cs-state {
+ pins = "gpio13";
+ function = "qup2_se0";
+ };
+
+ qup_spi16_cs_gpio: qup-spi16-cs-gpio-state {
+ pins = "gpio13";
+ function = "gpio";
+ };
+
+ qup_uart0_cts: qup-uart0-cts-state {
+ pins = "gpio17";
+ function = "qup0_se0";
+ };
+
+ qup_uart0_rts: qup-uart0-rts-state {
+ pins = "gpio18";
+ function = "qup0_se0";
+ };
+
+ qup_uart0_tx: qup-uart0-tx-state {
+ pins = "gpio19";
+ function = "qup0_se0";
+ };
+
+ qup_uart0_rx: qup-uart0-rx-state {
+ pins = "gpio20";
+ function = "qup0_se0";
+ };
+
+ qup_uart1_cts: qup-uart1-cts-state {
+ pins = "gpio19";
+ function = "qup0_se1";
+ };
+
+ qup_uart1_rts: qup-uart1-rts-state {
+ pins = "gpio20";
+ function = "qup0_se1";
+ };
+
+ qup_uart1_tx: qup-uart1-tx-state {
+ pins = "gpio17";
+ function = "qup0_se1";
+ };
+
+ qup_uart1_rx: qup-uart1-rx-state {
+ pins = "gpio18";
+ function = "qup0_se1";
+ };
+
+ qup_uart2_cts: qup-uart2-cts-state {
+ pins = "gpio33";
+ function = "qup0_se2";
+ };
+
+ qup_uart2_rts: qup-uart2-rts-state {
+ pins = "gpio34";
+ function = "qup0_se2";
+ };
+
+ qup_uart2_tx: qup-uart2-tx-state {
+ pins = "gpio35";
+ function = "qup0_se2";
+ };
+
+ qup_uart2_rx: qup-uart2-rx-state {
+ pins = "gpio36";
+ function = "qup0_se2";
+ };
+
+ qup_uart3_cts: qup-uart3-cts-state {
+ pins = "gpio25";
+ function = "qup0_se3";
+ };
+
+ qup_uart3_rts: qup-uart3-rts-state {
+ pins = "gpio26";
+ function = "qup0_se3";
+ };
+
+ qup_uart3_tx: qup-uart3-tx-state {
+ pins = "gpio27";
+ function = "qup0_se3";
+ };
+
+ qup_uart3_rx: qup-uart3-rx-state {
+ pins = "gpio28";
+ function = "qup0_se3";
+ };
+
+ qup_uart4_cts: qup-uart4-cts-state {
+ pins = "gpio29";
+ function = "qup0_se4";
+ };
+
+ qup_uart4_rts: qup-uart4-rts-state {
+ pins = "gpio30";
+ function = "qup0_se4";
+ };
+
+ qup_uart4_tx: qup-uart4-tx-state {
+ pins = "gpio31";
+ function = "qup0_se4";
+ };
+
+ qup_uart4_rx: qup-uart4-rx-state {
+ pins = "gpio32";
+ function = "qup0_se4";
+ };
+
+ qup_uart5_cts: qup-uart5-cts-state {
+ pins = "gpio21";
+ function = "qup0_se5";
+ };
+
+ qup_uart5_rts: qup-uart5-rts-state {
+ pins = "gpio22";
+ function = "qup0_se5";
+ };
+
+ qup_uart5_tx: qup-uart5-tx-state {
+ pins = "gpio23";
+ function = "qup0_se5";
+ };
+
+ qup_uart5_rx: qup-uart5-rx-state {
+ pins = "gpio23";
+ function = "qup0_se5";
+ };
+
+ qup_uart6_cts: qup-uart6-cts-state {
+ pins = "gpio80";
+ function = "qup0_se6";
+ };
+
+ qup_uart6_rts: qup-uart6-rts-state {
+ pins = "gpio81";
+ function = "qup0_se6";
+ };
+
+ qup_uart6_tx: qup-uart6-tx-state {
+ pins = "gpio82";
+ function = "qup0_se6";
+ };
+
+ qup_uart6_rx: qup-uart6-rx-state {
+ pins = "gpio83";
+ function = "qup0_se6";
+ };
+
+ qup_uart7_tx: qup-uart7-tx-state {
+ pins = "gpio43";
+ function = "qup0_se7";
+ };
+
+ qup_uart7_rx: qup-uart7-rx-state {
+ pins = "gpio44";
function = "qup0_se7";
};
+
+ qup_uart8_cts: qup-uart8-cts-state {
+ pins = "gpio37";
+ function = "qup1_se0";
+ };
+
+ qup_uart8_rts: qup-uart8-rts-state {
+ pins = "gpio38";
+ function = "qup1_se0";
+ };
+
+ qup_uart8_tx: qup-uart8-tx-state {
+ pins = "gpio39";
+ function = "qup1_se0";
+ };
+
+ qup_uart8_rx: qup-uart8-rx-state {
+ pins = "gpio40";
+ function = "qup1_se0";
+ };
+
+ qup_uart9_cts: qup-uart9-cts-state {
+ pins = "gpio39";
+ function = "qup1_se1";
+ };
+
+ qup_uart9_rts: qup-uart9-rts-state {
+ pins = "gpio40";
+ function = "qup1_se1";
+ };
+
+ qup_uart9_tx: qup-uart9-tx-state {
+ pins = "gpio37";
+ function = "qup1_se1";
+ };
+
+ qup_uart9_rx: qup-uart9-rx-state {
+ pins = "gpio38";
+ function = "qup1_se1";
+ };
+
+ qup_uart10_cts: qup-uart10-cts-state {
+ pins = "gpio84";
+ function = "qup1_se2";
+ };
+
+ qup_uart10_rts: qup-uart10-rts-state {
+ pins = "gpio84";
+ function = "qup1_se2";
+ };
+
+ qup_uart10_tx: qup-uart10-tx-state {
+ pins = "gpio85";
+ function = "qup1_se2";
+ };
+
+ qup_uart10_rx: qup-uart10-rx-state {
+ pins = "gpio87";
+ function = "qup1_se2";
+ };
+
+ qup_uart11_tx: qup-uart11-tx-state {
+ pins = "gpio41";
+ function = "qup1_se3";
+ };
+
+ qup_uart11_rx: qup-uart11-rx-state {
+ pins = "gpio42";
+ function = "qup1_se3";
+ };
+
+ qup_uart12_cts: qup-uart12-cts-state {
+ pins = "gpio45";
+ function = "qup1_se4";
+ };
+
+ qup_uart12_rts: qup-uart12-rts-state {
+ pins = "gpio46";
+ function = "qup1_se4";
+ };
+
+ qup_uart12_tx: qup-uart12-tx-state {
+ pins = "gpio47";
+ function = "qup1_se4";
+ };
+
+ qup_uart12_rx: qup-uart12-rx-state {
+ pins = "gpio48";
+ function = "qup1_se4";
+ };
+
+ qup_uart13_cts: qup-uart13-cts-state {
+ pins = "gpio49";
+ function = "qup1_se5";
+ };
+
+ qup_uart13_rts: qup-uart13-rts-state {
+ pins = "gpio50";
+ function = "qup1_se5";
+ };
+
+ qup_uart13_tx: qup-uart13-tx-state {
+ pins = "gpio51";
+ function = "qup1_se5";
+ };
+
+ qup_uart13_rx: qup-uart13-rx-state {
+ pins = "gpio52";
+ function = "qup1_se5";
+ };
+
+ qup_uart14_cts: qup-uart14-cts-state {
+ pins = "gpio89";
+ function = "qup1_se6";
+ };
+
+ qup_uart14_rts: qup-uart14-rts-state {
+ pins = "gpio90";
+ function = "qup1_se6";
+ };
+
+ qup_uart14_tx: qup-uart14-tx-state {
+ pins = "gpio91";
+ function = "qup1_se6";
+ };
+
+ qup_uart14_rx: qup-uart14-rx-state {
+ pins = "gpio92";
+ function = "qup1_se6";
+ };
+
+ qup_uart15_cts: qup-uart15-cts-state {
+ pins = "gpio91";
+ function = "qup1_se7";
+ };
+
+ qup_uart15_rts: qup-uart15-rts-state {
+ pins = "gpio92";
+ function = "qup1_se7";
+ };
+
+ qup_uart15_tx: qup-uart15-tx-state {
+ pins = "gpio89";
+ function = "qup1_se7";
+ };
+
+ qup_uart15_rx: qup-uart15-rx-state {
+ pins = "gpio90";
+ function = "qup1_se7";
+ };
+
+ qup_uart16_cts: qup-uart16-cts-state {
+ pins = "gpio10";
+ function = "qup2_se0";
+ };
+
+ qup_uart16_rts: qup-uart16-rts-state {
+ pins = "gpio11";
+ function = "qup2_se0";
+ };
+
+ qup_uart16_tx: qup-uart16-tx-state {
+ pins = "gpio12";
+ function = "qup2_se0";
+ };
+
+ qup_uart16_rx: qup-uart16-rx-state {
+ pins = "gpio13";
+ function = "qup2_se0";
+ };
};
sram: sram@146d8000 {
--
2.17.1