Re: [PATCH tty-next v3 1/6] serial: 8250: Adjust the timeout for FIFO mode

[Wander Lairson Costa]

On Fri, Oct 25, 2024 at 04:45:02PM +0300, Andy Shevchenko wrote:
> On Fri, Oct 25, 2024 at 01:03:23PM +0206, John Ogness wrote:
> > After a console has fed a line into TX, it uses wait_for_xmitr()
> > to wait until the data has been sent out before returning to the
> > printk code. However, wait_for_xmitr() will timeout after 10ms,
> 
> printk here is a function reference or module?
> For the latter I would use the filename to be sure it's clear,
> like printk.c. For the former (and it seems you know that)
> we may use printk().
> 
> > regardless if the data has been transmitted or not.
> > 
> > For single bytes, this timeout is sufficient even at very slow
> > baud rates, such as 1200bps. However, when FIFO mode is used,
> > there may be 64 bytes pushed into the FIFO at once. At a baud
> > rate of 115200bps, the 10ms timeout is still sufficient.
> > However, when using lower baud rates (such as 57600bps), the
> > timeout is _not_ sufficient. This causes longer lines to be cut
> > off, resulting in lost and horribly misformatted output on the
> > console.
> > 
> > When using FIFO mode, take the number of bytes into account to
> > determine an appropriate max timeout. Increasing the timeout
> 
> maximum
> (in order not to mix with max() function)
> 
> > does not affect performance since ideally the timeout never
> > occurs.
> 
> ...
> 
> >  /*
> >   *	Wait for transmitter & holding register to empty
> > + *	with timeout
> 
> Can you fix the style while at it?
> 
> >   */
> 
>  /* Wait for transmitter & holding register to empty with timeout */
> 
> ...
> 
> >  static void serial8250_console_fifo_write(struct uart_8250_port *up,
> >  					  const char *s, unsigned int count)
> >  {
> > -	int i;
> >  	const char *end = s + count;
> >  	unsigned int fifosize = up->tx_loadsz;
> > +	unsigned int tx_count = 0;
> >  	bool cr_sent = false;
> > +	unsigned int i;
> >  
> >  	while (s != end) {
> > -		wait_for_lsr(up, UART_LSR_THRE);
> > +		/* Allow timeout for each byte of a possibly full FIFO. */
> 
> Does the one-line comment style in this file use periods? If not, drop,
> otherwise apply it to the above proposal.
> 
> > +		for (i = 0; i < fifosize; i++) {
> > +			if (wait_for_lsr(up, UART_LSR_THRE))
> > +				break;
> > +		}
> 
> > +	}
> > +
> > +	/* Allow timeout for each byte written. */
> > +	for (i = 0; i < tx_count; i++) {
> > +		if (wait_for_lsr(up, UART_LSR_THRE))
> > +			break;
> 
> This effectively repeats the above. Even for the fix case I would still add
> a new helper to deduplicate.

+1

With this fixed, Reviewed-by: Wander Lairson Costa <wander@xxxxxxxxxx>
> 
> >  	}
> >  }
> 
> -- 
> With Best Regards,
> Andy Shevchenko
> 
>