[PATCH v4 2/3] can: flexcan: Add quirk to handle separate interrupt lines for mailboxes

[Ciprian Costea]

From: Ciprian Marian Costea <ciprianmarian.costea@xxxxxxxxxxx>

Introduce 'FLEXCAN_QUIRK_SECONDARY_MB_IRQ' quirk to handle a FlexCAN
hardware module integration particularity where two ranges of mailboxes
are controlled by separate hardware interrupt lines.
The same 'flexcan_irq' handler is used for both separate mailbox interrupt
lines, with no other changes.

Signed-off-by: Ciprian Marian Costea <ciprianmarian.costea@xxxxxxxxxxx>
Reviewed-by: Vincent Mailhol <mailhol.vincent@xxxxxxxxxx>
---
 drivers/net/can/flexcan/flexcan-core.c | 24 +++++++++++++++++++++++-
 drivers/net/can/flexcan/flexcan.h      |  5 +++++
 2 files changed, 28 insertions(+), 1 deletion(-)

diff --git a/drivers/net/can/flexcan/flexcan-core.c b/drivers/net/can/flexcan/flexcan-core.c
index ac1a860986df..3ae54305bf33 100644
--- a/drivers/net/can/flexcan/flexcan-core.c
+++ b/drivers/net/can/flexcan/flexcan-core.c
@@ -1762,14 +1762,25 @@ static int flexcan_open(struct net_device *dev)
 			goto out_free_irq_boff;
 	}
 
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SECONDARY_MB_IRQ) {
+		err = request_irq(priv->irq_secondary_mb,
+				  flexcan_irq, IRQF_SHARED, dev->name, dev);
+		if (err)
+			goto out_free_irq_err;
+	}
+
 	flexcan_chip_interrupts_enable(dev);
 
 	netif_start_queue(dev);
 
 	return 0;
 
+ out_free_irq_err:
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_IRQ_3)
+		free_irq(priv->irq_err, dev);
  out_free_irq_boff:
-	free_irq(priv->irq_boff, dev);
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_NR_IRQ_3)
+		free_irq(priv->irq_boff, dev);
  out_free_irq:
 	free_irq(dev->irq, dev);
  out_can_rx_offload_disable:
@@ -1799,6 +1810,9 @@ static int flexcan_close(struct net_device *dev)
 		free_irq(priv->irq_boff, dev);
 	}
 
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SECONDARY_MB_IRQ)
+		free_irq(priv->irq_secondary_mb, dev);
+
 	free_irq(dev->irq, dev);
 	can_rx_offload_disable(&priv->offload);
 	flexcan_chip_stop_disable_on_error(dev);
@@ -2187,6 +2201,14 @@ static int flexcan_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SECONDARY_MB_IRQ) {
+		priv->irq_secondary_mb = platform_get_irq_byname(pdev, "mb-1");
+		if (priv->irq_secondary_mb < 0) {
+			err = priv->irq_secondary_mb;
+			goto failed_platform_get_irq;
+		}
+	}
+
 	if (priv->devtype_data.quirks & FLEXCAN_QUIRK_SUPPORT_FD) {
 		priv->can.ctrlmode_supported |= CAN_CTRLMODE_FD |
 			CAN_CTRLMODE_FD_NON_ISO;
diff --git a/drivers/net/can/flexcan/flexcan.h b/drivers/net/can/flexcan/flexcan.h
index 4933d8c7439e..2cf886618c96 100644
--- a/drivers/net/can/flexcan/flexcan.h
+++ b/drivers/net/can/flexcan/flexcan.h
@@ -70,6 +70,10 @@
 #define FLEXCAN_QUIRK_SUPPORT_RX_FIFO BIT(16)
 /* Setup stop mode with ATF SCMI protocol to support wakeup */
 #define FLEXCAN_QUIRK_SETUP_STOP_MODE_SCMI BIT(17)
+/* Device has two separate interrupt lines for two mailbox ranges, which
+ * both need to have an interrupt handler registered.
+ */
+#define FLEXCAN_QUIRK_SECONDARY_MB_IRQ	BIT(18)
 
 struct flexcan_devtype_data {
 	u32 quirks;		/* quirks needed for different IP cores */
@@ -107,6 +111,7 @@ struct flexcan_priv {
 
 	int irq_boff;
 	int irq_err;
+	int irq_secondary_mb;
 
 	/* IPC handle when setup stop mode by System Controller firmware(scfw) */
 	struct imx_sc_ipc *sc_ipc_handle;
-- 
2.45.2