Re: [PATCH v1 4/7] soc: qcom: geni-se:: Add support to load QUP SE Firmware via Linux subsystem

[neil . armstrong]

Hi,

On 04/12/2024 16:03, Viken Dadhaniya wrote:
> Load the firmware to QUP SE based on the "qcom,load-firmware" property
> specified in devicetree. Populate Serial engine and base address details
> in the probe function of the protocol driver and pass to firmware load
> routine.
>
> Skip the firmware loading if the firmware is already loaded in Serial
> Engine's firmware memory area.
>
> Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
> Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
> Signed-off-by: Viken Dadhaniya <quic_vdadhani@xxxxxxxxxxx>
> ---
>   drivers/soc/qcom/qcom-geni-se.c      | 445 +++++++++++++++++++++++++++
>   include/linux/soc/qcom/geni-se.h     |  17 +
>   include/linux/soc/qcom/qup-fw-load.h | 179 +++++++++++
>   3 files changed, 641 insertions(+)
>   create mode 100644 include/linux/soc/qcom/qup-fw-load.h
>
> diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
> index 4cb959106efa..423102fac3fc 100644
> --- a/drivers/soc/qcom/qcom-geni-se.c
> +++ b/drivers/soc/qcom/qcom-geni-se.c
> @@ -1,5 +1,6 @@
>   // SPDX-License-Identifier: GPL-2.0
>   // Copyright (c) 2017-2018, The Linux Foundation. All rights reserved.
> +// Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
>   
>   /* Disable MMIO tracing to prevent excessive logging of unwanted MMIO traces */
>   #define __DISABLE_TRACE_MMIO__
> @@ -15,6 +16,7 @@
>   #include <linux/pinctrl/consumer.h>
>   #include <linux/platform_device.h>
>   #include <linux/soc/qcom/geni-se.h>
> +#include <linux/soc/qcom/qup-fw-load.h>
>   
>   /**
>    * DOC: Overview
> @@ -97,6 +99,9 @@ struct geni_wrapper {
>   	unsigned int num_clks;
>   };
>   
> +/* elf file should be at /lib/firmware/ */
> +#define QUP_FW_ELF_FILE	"qupv3fw.elf"

I supposed the qupv3fw.elf is SoC specific, so it should use /lib/firmware/qcom
base path and also a SoC/platform specific path that should be specified
with firmware-name in DT.

With this property, "qcom,load-firmware" could be dropped.

> +
>   /**
>    * struct geni_se_desc - Data structure to represent the QUP Wrapper resources
>    * @clks:		Name of the primary & optional secondary AHB clocks
> @@ -110,6 +115,9 @@ struct geni_se_desc {
>   static const char * const icc_path_names[] = {"qup-core", "qup-config",
>   						"qup-memory"};
>   
> +static const char * const protocol_name[] = { "None", "SPI", "UART",
> +					      "I2C", "I3C", "SPI SLAVE"};
> +
>   #define QUP_HW_VER_REG			0x4
>   
<snip>