Re: [net-next PATCH v9 3/4] net: dsa: Add Airoha AN8855 5-Port Gigabit DSA Switch driver

[Christian Marangi]

On Thu, Dec 05, 2024 at 06:27:59PM +0200, Vladimir Oltean wrote:
> On Thu, Dec 05, 2024 at 03:51:33PM +0100, Christian Marangi wrote:
> > +static int an8855_efuse_read(void *context, unsigned int offset,
> > +			     void *val, size_t bytes)
> > +{
> > +	struct an8855_priv *priv = context;
> > +
> > +	return regmap_bulk_read(priv->regmap, AN8855_EFUSE_DATA0 + offset,
> > +				val, bytes / sizeof(u32));
> > +}
> > +
> > +static struct nvmem_config an8855_nvmem_config = {
> > +	.name = "an8855-efuse",
> > +	.size = AN8855_EFUSE_CELL * sizeof(u32),
> > +	.stride = sizeof(u32),
> > +	.word_size = sizeof(u32),
> > +	.reg_read = an8855_efuse_read,
> > +};
> > +
> > +static int an8855_sw_register_nvmem(struct an8855_priv *priv)
> > +{
> > +	struct nvmem_device *nvmem;
> > +
> > +	an8855_nvmem_config.priv = priv;
> > +	an8855_nvmem_config.dev = priv->dev;
> > +	nvmem = devm_nvmem_register(priv->dev, &an8855_nvmem_config);
> > +	if (IS_ERR(nvmem))
> > +		return PTR_ERR(nvmem);
> > +
> > +	return 0;
> > +}
> 
> At some point we should enforce the rule that new drivers for switch
> SoCs with complex peripherals should use MFD and move all non-networking
> peripherals to drivers handled by their respective subsystems.
> 
> I don't have the expertise to review a nvmem driver, and the majority of
> them are in drivers/nvmem, with a dedicated subsystem and maintainer.
> In general I want to make sure it is clear that I don't encourage the
> model where DSA owns the entire mdio_device.
> 
> What other peripherals are there on this SoC other than an MDIO bus and
> an EFUSE? IRQCHIP, GPIOs, LED controller, sensors?
> 
> You can take a look at drivers/mfd/ocelot* and
> Documentation/devicetree/bindings/mfd/mscc,ocelot.yaml for an example on
> how to use mfd for the top-level MDIO device, and DSA as just the driver
> for the Ethernet switch component (which will be represented as a
> platform_device).

Hi Vladimir,

I checked the examples and one problems that comes to me is how to model
this if only MDIO is used as a comunication method. Ocelot have PCIE or
SPI but this switch only comunicate with MDIO on his address. So where
should I place the SoC or MFD node? In the switch root node?

Also the big problem is how to model accessing the register with MDIO
with an MFD implementation.

Anyway just to make sure the Switch SoC doesn't expose an actualy MDIO
bus, that is just to solve the problem with the Switch Address shared
with one of the port. (Switch Address can be accessed by every switch
port with a specific page set)

But yes the problem is there... Function is not implemented but the
switch have i2c interface, minimal CPU, GPIO and Timer in it.

Happy to make the required changes, just very confused on how the final
DT node structure.

-- 
	Ansuel