Re: [PATCH] regulator:s5m8767 Fully convert to GPIO descriptors

[Song Chen]

hi Krzysztof,

It's clear, will send a v2 soon.

Best regards,

Song

在 2024/12/10 03:50, Krzysztof Kozlowski 写道:
> On 07/12/2024 07:16, Song Chen wrote:
> > > >    		}
> > > > -		pdata->buck_gpios[i] = gpio;
> > > > +
> > > > +		/* SET GPIO*/
> > >
> > > What is a SET GPIO?
> > >
> > > > +		snprintf(label, sizeof(label), "%s%d", "S5M8767 SET", i + 1);
> > >
> > > Why using "SET" as name, not the actual name it is used for? Buck DVS?
> >
> > from below snippets:
> > s5m8767_pmic_probe of drivers/regulator/s5m8767.c
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[0],
> >                       "S5M8767 SET1");
> >           if (ret)
> >               return ret;
> >
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[1],
> >                       "S5M8767 SET2");
> >           if (ret)
> >               return ret;
> >
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[2],
> >                       "S5M8767 SET3");
>
>
> Yeah, your code is fine.
>
> > and arch/arm/boot/dts/samsung/exynos5250-spring.dts
> >
> >           s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>, /* DVS1 */
> >                             <&gpd1 1 GPIO_ACTIVE_LOW>, /* DVS2 */
> >                             <&gpd1 2 GPIO_ACTIVE_LOW>; /* DVS3 */
> >
> >           s5m8767,pmic-buck-ds-gpios = <&gpx2 3 GPIO_ACTIVE_LOW>, /* SET1 */
> >                            <&gpx2 4 GPIO_ACTIVE_LOW>, /* SET2 */
> >                            <&gpx2 5 GPIO_ACTIVE_LOW>; /* SET3 */
> >
> > > > +		gpiod_set_consumer_name(pdata->buck_gpios[i], label);
> > > > +		gpiod_direction_output(pdata->buck_gpios[i],
> > > > +					(pdata->buck_default_idx >> (2 - i)) & 0x1);
> > >
> > > This is not an equivalent code. You set values for GPIOs 0-1 even if
> > > requesting GPIO 2 fails.
> > >
> > > On which board did you test it?
> >
> > You are right ,it's not equivalent with original code, i will fix it.
> > but i have a question here:
> >
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[0],
> >                       "S5M8767 SET1");
> >           if (ret)
> >               return ret;
> >
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[1],
> >                       "S5M8767 SET2");
> >           if (ret)
> >               return ret;
> >
> >           ret = devm_gpio_request(&pdev->dev, pdata->buck_gpios[2],
> >                       "S5M8767 SET3");
> >           if (ret)
> >               return ret;
> >
> > if it fails to request buck_gpios[2] after successfully requests
> > buck_gpios[0] and buck_gpios[1], the probe fails as well, should it call
> > gpiod_put to return gpio resource?
>
>
> Aren't you using devm interface? Please read the API. You do not need to
> put anything, unless you use some other interface and I missed the point
> of the question.

Not until you told me, I read the devm code, devres_release_all releases 
gpio resources eventually by calling dr->node.release(devm_gpiod_release).

many thanks.

> Best regards,
> Krzysztof