Re: [PATCH] usb: cdns3: exit cdns3_gadget_udc_start if FAST_REG_ACCESS cannot be set
From: Peter Chen
Date: Sat Feb 08 2025 - 00:40:04 EST
On 25-02-07 11:12:50, Siddharth Vadapalli wrote:
> On Fri, Feb 07, 2025 at 10:25:23AM +0800, Peter Chen wrote:
>
> Hello Peter,
>
> > On 25-02-06 18:29:36, Siddharth Vadapalli wrote:
> > > When the device is in a low power state, access to the following
> > > registers takes a long time:
> > > - EP_CFG
> > > - EP_TRADDR
> > > - EP_CMD
> > > - EP_SEL
> > > - EP_STS
> > > - USB_CONF
> > >
> > > To address this, the fast register access feature can be enabled by
> > > setting PUSB_PWR_FST_REG_ACCESS bit of the USB_PWR register, which
> > > allows quick access by software. Software is expected to poll on
> > > PUSB_PWR_FST_REG_ACCESS_STAT to ensure that fast register access has
> > > been enabled by the controller. Attempting to access any of the
> > > aforementioned registers after setting PUSB_PWR_FST_REG_ACCESS but
> > > before PUSB_PWR_FST_REG_ACCESS_STAT has been set will result in
> > > undefined behavior and potentially result in system hang.
> > >
> > > Hence, poll on PUSB_PWR_FST_REG_ACCESS_STAT before proceeding with
> > > gadget configuration, and exit if it cannot be enabled.
> > >
> > > Fixes: b5148d946f45 ("usb: cdns3: gadget: set fast access bit")
> > > Cc: <stable@xxxxxxxxxxxxxxx>
> > > Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
> > > ---
> > >
> > > Hello,
> > >
> > > This patch is based on commit
> > > 92514ef226f5 Merge tag 'for-6.14-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
> > > of Mainline Linux.
> > >
> > > Regards,
> > > Siddharth.
> > >
> > > drivers/usb/cdns3/cdns3-gadget.c | 18 ++++++++++++++++--
> > > 1 file changed, 16 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/usb/cdns3/cdns3-gadget.c b/drivers/usb/cdns3/cdns3-gadget.c
> > > index fd1beb10bba7..b62691944272 100644
> > > --- a/drivers/usb/cdns3/cdns3-gadget.c
> > > +++ b/drivers/usb/cdns3/cdns3-gadget.c
> > > @@ -2971,8 +2971,6 @@ static void cdns3_gadget_config(struct cdns3_device *priv_dev)
> > > /* enable generic interrupt*/
> > > writel(USB_IEN_INIT, ®s->usb_ien);
> > > writel(USB_CONF_CLK2OFFDS | USB_CONF_L1DS, ®s->usb_conf);
> > > - /* keep Fast Access bit */
> > > - writel(PUSB_PWR_FST_REG_ACCESS, &priv_dev->regs->usb_pwr);
> > >
> > > cdns3_configure_dmult(priv_dev, NULL);
> > > }
> > > @@ -2990,6 +2988,8 @@ static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
> > > struct cdns3_device *priv_dev = gadget_to_cdns3_device(gadget);
> > > unsigned long flags;
> > > enum usb_device_speed max_speed = driver->max_speed;
> > > + int ret;
> > > + u32 reg;
> > >
> > > spin_lock_irqsave(&priv_dev->lock, flags);
> > > priv_dev->gadget_driver = driver;
> > > @@ -2997,6 +2997,20 @@ static int cdns3_gadget_udc_start(struct usb_gadget *gadget,
> > > /* limit speed if necessary */
> > > max_speed = min(driver->max_speed, gadget->max_speed);
> > >
> > > + /* keep Fast Access bit */
> > > + writel(PUSB_PWR_FST_REG_ACCESS, &priv_dev->regs->usb_pwr);
> > > + reg = readl(&priv_dev->regs->usb_pwr);
> > > + if (!(reg & PUSB_PWR_FST_REG_ACCESS_STAT)) {
> > > + ret = readl_poll_timeout_atomic(&priv_dev->regs->usb_pwr, reg,
> > > + (reg & PUSB_PWR_FST_REG_ACCESS_STAT),
> > > + 10, 1000);
> > > + if (ret) {
> > > + dev_err(priv_dev->dev, "Failed to enable fast access\n");
> > > + spin_unlock_irqrestore(&priv_dev->lock, flags);
> > > + return ret;
> > > + }
> > > + }
> > > +
> > > switch (max_speed) {
> > > case USB_SPEED_FULL:
> > > writel(USB_CONF_SFORCE_FS, &priv_dev->regs->usb_conf);
> >
> > Hi Siddharth,
> >
> > Would you please keep this change at cdns3_gadget_config in case the
> > controller is power lost during the system suspend?
>
> I did think of that initially, but the problem with doing so is that we
> are already accessing USB_CONF above in the "switch(max_speed)" section.
> The PUSB_PWR_FST_REG_ACCESS bit needs to be set before accessing any of:
> - EP_CFG
> - EP_TRADDR
> - EP_CMD
> - EP_SEL
> - EP_STS
> - USB_CONF
>
> Please let me know if you have an alternate suggestion to address the
> above.
>
How about move cdns3_gadget_config at the beginning of function
cdns3_gadget_udc_start, and add your changes at cdns3_gadget_config?
Regards,
Peter