Re: [PATCH v3 03/18] cxl/pci: cxl_hdm_decode_init: Move comment

From: Robert Richter
Date: Wed Feb 12 2025 - 19:35:46 EST


On 12.02.25 18:09:10, Jonathan Cameron wrote:
> On Tue, 11 Feb 2025 10:53:33 +0100
> Robert Richter <rrichter@xxxxxxx> wrote:
>
> > The comment applies to the check, move it there.
>
> I think I disagree. It was in the right place as far as I can tell.
> It is an odd place for comment, but it's kind of describing
> why it is not an error to get down there.

Ah, that was not obvious to the reader. :-)

>
> >
> > Signed-off-by: Robert Richter <rrichter@xxxxxxx>
> > Reviewed-by: Gregory Price <gourry@xxxxxxxxxx>
> > Tested-by: Gregory Price <gourry@xxxxxxxxxx>
> > ---
> > drivers/cxl/core/pci.c | 18 +++++++++---------
> > 1 file changed, 9 insertions(+), 9 deletions(-)
> >
> > diff --git a/drivers/cxl/core/pci.c b/drivers/cxl/core/pci.c
> > index f8e22bc278c3..c49efc419285 100644
> > --- a/drivers/cxl/core/pci.c
> > +++ b/drivers/cxl/core/pci.c
> > @@ -419,6 +419,15 @@ int cxl_hdm_decode_init(struct cxl_dev_state *cxlds, struct cxl_hdm *cxlhdm,
> > if (!hdm)
> > return -ENODEV;
> >
> > + /*
> > + * Per CXL 2.0 Section 8.1.3.8.3 and 8.1.3.8.4 DVSEC CXL Range 1 Base
> > + * [High,Low] when HDM operation is enabled the range register values
> > + * are ignored by the device, but the spec also recommends matching the
> > + * DVSEC Range 1,2 to HDM Decoder Range 0,1. So, non-zero info->ranges
> > + * are expected even though Linux does not require or maintain that
> > + * match. If at least one DVSEC range is enabled and allowed, skip HDM
> > + * Decoder Capability Enable.
>
> This check is about mem_enabled. Would be fine to add another comment here to
> say.

The next patch extends the comment for more clarification (I hope so).

>
> /*
> * If mem_enabled is not set prior configuration is irrelevant and we
> * can do what we like so enable HDM decoders and ignore DVSEC registers.
> */
> > + */
> > if (!info->mem_enabled) {
> > rc = devm_cxl_enable_hdm(&port->dev, cxlhdm);
> > if (rc)
> > @@ -454,15 +463,6 @@ int cxl_hdm_decode_init(struct cxl_dev_state *cxlds, struct cxl_hdm *cxlhdm,
> > return -ENXIO;
> > }
> >
> > - /*
> > - * Per CXL 2.0 Section 8.1.3.8.3 and 8.1.3.8.4 DVSEC CXL Range 1 Base
> > - * [High,Low] when HDM operation is enabled the range register values
> > - * are ignored by the device, but the spec also recommends matching the
> > - * DVSEC Range 1,2 to HDM Decoder Range 0,1. So, non-zero info->ranges
> > - * are expected even though Linux does not require or maintain that
> > - * match. If at least one DVSEC range is enabled and allowed, skip HDM
> > - * Decoder Capability Enable.
> > - */
>
> This is the path the comment is talking about because only if we get to this
> return path are we 'skipping' the HDM decoder capability and not returning
> an error. The path representing an HDM decoder equipped device that
> was configured by a BIOS that decided to use the DVSEC registers.
>
> I'm not sure why we care about how the hdm decoders are programmed inthis
> case though.
>
> I'm confused :(

There is an HDM, but it is disabled (CXL_HDM_DECODER_ENABLE is
cleared). If the DVSEC range regs do not have valid values
(!info->mem_enabled, firmware indicates it is not used), just go and
enable the HDM.

We try to use the hdm decoders here to be able to use them for a
non-auto setup. Else, decoder emulation is used
(should_emulate_decoders()) and decoders are locked
(CXL_DECODER_F_LOCK will be set).

Maybe take a look at the whole change with added comments including
patch 4/18?

I hope to not add confusion here. :-)

-Robert

>
> > return 0;
> > }
> > EXPORT_SYMBOL_NS_GPL(cxl_hdm_decode_init, "CXL");
>