Re: [PATCH v4 2/2] arm64: dts: qcom: ipq5424: Enable PCIe PHYs and controllers

[Dmitry Baryshkov]

On Thu, Feb 13, 2025 at 12:49:12PM +0530, Manikanta Mylavarapu wrote:
> Enable the PCIe controller and PHY nodes corresponding to RDP466.
> 
> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@xxxxxxxxxxx>
> ---
> Changes in V4:
> 	- Added a new line before status in pcie2 and pcie3 nodes.
> 	- Dropped 'output-low' property from pcie2-default-state and
> 	  pcie3-default-state nodes.
> 
>  arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts | 41 ++++++++++++++++++++-
>  1 file changed, 40 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> index b6e4bb3328b3..e73f61266012 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq5424-rdp466.dts
> @@ -53,6 +53,32 @@ &dwc_1 {
>  	dr_mode = "host";
>  };
>  
> +&pcie2 {
> +	pinctrl-0 = <&pcie2_default_state>;
> +	pinctrl-names = "default";
> +
> +	perst-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;

Don't you also need wake-gpios? Here and in pcie3.

> +
> +	status = "okay";
> +};
> +
> +&pcie2_phy {
> +	status = "okay";
> +};
> +
> +&pcie3 {
> +	pinctrl-0 = <&pcie3_default_state>;
> +	pinctrl-names = "default";
> +
> +	perst-gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
> +
> +	status = "okay";
> +};
> +
> +&pcie3_phy {
> +	status = "okay";
> +};
> +
>  &qusb_phy_0 {
>  	vdd-supply = <&vreg_misc_0p925>;
>  	vdda-pll-supply = <&vreg_misc_1p8>;
> @@ -147,6 +173,20 @@ data-pins {
>  			bias-pull-up;
>  		};
>  	};
> +
> +	pcie2_default_state: pcie2-default-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-up;
> +	};
> +
> +	pcie3_default_state: pcie3-default-state {
> +		pins = "gpio34";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-up;
> +	};
>  };
>  
>  &uart1 {
> @@ -166,4 +206,3 @@ &usb3 {
>  &xo_board {
>  	clock-frequency = <24000000>;
>  };
> -
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry