[PATCH v3 1/3] scsi: hisi_sas: Enable force phy when SATA disk directly connected

[Xingui Yang]

the SAS controller determines the disk to which I/Os are delivered based
on the port id in the DQ entry when SATA disk directly connected.

When many phys were disconnected immediately and connected again during
I/O sending and port id of phys were changed and used by other link, I/O
may be sent to incorrect disk and data inconsistency on the SATA disk may
occur during I/O retry with the old port id. So enable force phy, then
force the command to be executed in a certain phy, and if the actual phy
id of the port does not match the phy configured in the command, the chip
will stop delivering the I/O to disk.

Fixes: ce60689e12dd ("scsi: hisi_sas: add v3 code to send ATA frame")
Signed-off-by: Xingui Yang <yangxingui@xxxxxxxxxx>
Reviewed-by: Yihang Li <liyihang9@xxxxxxxxxx>
---
 drivers/scsi/hisi_sas/hisi_sas_v2_hw.c |  9 +++++++--
 drivers/scsi/hisi_sas/hisi_sas_v3_hw.c | 14 ++++++++++++--
 2 files changed, 19 insertions(+), 4 deletions(-)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
index 6e7f99fcc824..3af991cad07e 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v2_hw.c
@@ -2501,6 +2501,7 @@ static void prep_ata_v2_hw(struct hisi_hba *hisi_hba,
 	struct hisi_sas_port *port = to_hisi_sas_port(sas_port);
 	struct sas_ata_task *ata_task = &task->ata_task;
 	struct sas_tmf_task *tmf = slot->tmf;
+	int phy_id;
 	u8 *buf_cmd;
 	int has_data = 0, hdr_tag = 0;
 	u32 dw0, dw1 = 0, dw2 = 0;
@@ -2508,10 +2509,14 @@ static void prep_ata_v2_hw(struct hisi_hba *hisi_hba,
 	/* create header */
 	/* dw0 */
 	dw0 = port->id << CMD_HDR_PORT_OFF;
-	if (parent_dev && dev_is_expander(parent_dev->dev_type))
+	if (parent_dev && dev_is_expander(parent_dev->dev_type)) {
 		dw0 |= 3 << CMD_HDR_CMD_OFF;
-	else
+	} else {
+		phy_id = device->phy->identify.phy_identifier;
+		dw0 |= (1U << phy_id) << CMD_HDR_PHY_ID_OFF;
+		dw0 |= CMD_HDR_FORCE_PHY_MSK;
 		dw0 |= 4 << CMD_HDR_CMD_OFF;
+	}
 
 	if (tmf && ata_task->force_phy) {
 		dw0 |= CMD_HDR_FORCE_PHY_MSK;
diff --git a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
index 095bbf80c34e..6a0656f3b596 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_v3_hw.c
@@ -359,6 +359,10 @@
 #define CMD_HDR_RESP_REPORT_MSK		(0x1 << CMD_HDR_RESP_REPORT_OFF)
 #define CMD_HDR_TLR_CTRL_OFF		6
 #define CMD_HDR_TLR_CTRL_MSK		(0x3 << CMD_HDR_TLR_CTRL_OFF)
+#define CMD_HDR_PHY_ID_OFF		8
+#define CMD_HDR_PHY_ID_MSK		(0x1ff << CMD_HDR_PHY_ID_OFF)
+#define CMD_HDR_FORCE_PHY_OFF		17
+#define CMD_HDR_FORCE_PHY_MSK		(0x1U << CMD_HDR_FORCE_PHY_OFF)
 #define CMD_HDR_PORT_OFF		18
 #define CMD_HDR_PORT_MSK		(0xf << CMD_HDR_PORT_OFF)
 #define CMD_HDR_PRIORITY_OFF		27
@@ -1429,15 +1433,21 @@ static void prep_ata_v3_hw(struct hisi_hba *hisi_hba,
 	struct hisi_sas_cmd_hdr *hdr = slot->cmd_hdr;
 	struct asd_sas_port *sas_port = device->port;
 	struct hisi_sas_port *port = to_hisi_sas_port(sas_port);
+	int phy_id;
 	u8 *buf_cmd;
 	int has_data = 0, hdr_tag = 0;
 	u32 dw1 = 0, dw2 = 0;
 
 	hdr->dw0 = cpu_to_le32(port->id << CMD_HDR_PORT_OFF);
-	if (parent_dev && dev_is_expander(parent_dev->dev_type))
+	if (parent_dev && dev_is_expander(parent_dev->dev_type)) {
 		hdr->dw0 |= cpu_to_le32(3 << CMD_HDR_CMD_OFF);
-	else
+	} else {
+		phy_id = device->phy->identify.phy_identifier;
+		hdr->dw0 |= cpu_to_le32((1U << phy_id)
+				<< CMD_HDR_PHY_ID_OFF);
+		hdr->dw0 |= CMD_HDR_FORCE_PHY_MSK;
 		hdr->dw0 |= cpu_to_le32(4U << CMD_HDR_CMD_OFF);
+	}
 
 	switch (task->data_dir) {
 	case DMA_TO_DEVICE:
-- 
2.33.0