[PATCH 3/5] arm64: dts: ti: k3-am642-phyboard-electra: Add boot phase tags

[Wadim Egorov]

The bootph-all and bootph-pre-ram tags were introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across different
boot phases.

Add boot phase tags to all required nodes to ensure boot support from
all sources, including UART, Ethernet, uSD card, eMMC, and OSPI NOR Flash.

Signed-off-by: Wadim Egorov <w.egorov@xxxxxxxxx>
---
 arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi      | 12 ++++++++++++
 .../boot/dts/ti/k3-am642-phyboard-electra-rdk.dts    |  5 +++++
 2 files changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
index 99a6fdfaa7fb..52d53b690ac9 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
@@ -27,6 +27,7 @@ aliases {
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+		bootph-all;
 	};
 
 	reserved_memory: reserved-memory {
@@ -132,6 +133,7 @@ AM64X_IOPAD(0x01f8, PIN_INPUT, 4)	/* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
 			AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4)	/* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
 			AM64X_IOPAD(0x0100, PIN_OUTPUT, 7)	/* (V7) PRG1_PRU0_GPO18.GPIO0_63 */
 		>;
+		bootph-all;
 	};
 
 	cpsw_rgmii1_pins_default: cpsw-rgmii1-default-pins {
@@ -150,6 +152,7 @@ AM64X_IOPAD(0x01f4, PIN_INPUT, 4)	/* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */
 			AM64X_IOPAD(0x014c, PIN_OUTPUT, 4)	/* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
 			AM64X_IOPAD(0x0154, PIN_INPUT, 7)	/* (V12) PRG1_PRU1_GPO19.GPIO0_84 */
 		>;
+		bootph-all;
 	};
 
 	eeprom_wp_pins_default: eeprom-wp-default-pins {
@@ -169,6 +172,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
 			AM64X_IOPAD(0x0260, PIN_INPUT, 0)	/* (A18) I2C0_SCL */
 			AM64X_IOPAD(0x0264, PIN_INPUT, 0)	/* (B18) I2C0_SDA */
 		>;
+		bootph-all;
 	};
 
 	ospi0_pins_default: ospi0-default-pins {
@@ -185,6 +189,7 @@ AM64X_IOPAD(0x0024, PIN_INPUT, 0)	/* (N18) OSPI0_D6 */
 			AM64X_IOPAD(0x0028, PIN_INPUT, 0)	/* (M17) OSPI0_D7 */
 			AM64X_IOPAD(0x002c, PIN_OUTPUT, 0)	/* (L19) OSPI0_CSn0 */
 		>;
+		bootph-all;
 	};
 
 	rtc_pins_default: rtc-defaults-pins {
@@ -197,6 +202,7 @@ AM64X_IOPAD(0x0278, PIN_INPUT, 7)	/* (C19) EXTINTn.GPIO1_70 */
 &cpsw3g {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_rgmii1_pins_default>;
+	bootph-all;
 	status = "okay";
 };
 
@@ -204,6 +210,7 @@ &cpsw3g_mdio {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_mdio_pins_default>;
+	bootph-all;
 
 	cpsw3g_phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
@@ -215,12 +222,14 @@ cpsw3g_phy1: ethernet-phy@1 {
 		reset-gpios = <&main_gpio0 63 GPIO_ACTIVE_LOW>;
 		reset-assert-us = <1000>;
 		reset-deassert-us = <1000>;
+		bootph-all;
 	};
 };
 
 &cpsw_port1 {
 	phy-mode = "rgmii-rxid";
 	phy-handle = <&cpsw3g_phy1>;
+	bootph-all;
 	status = "okay";
 };
 
@@ -266,6 +275,7 @@ &main_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c0_pins_default>;
 	clock-frequency = <400000>;
+	bootph-all;
 
 	eeprom@50 {
 		compatible = "atmel,24c32";
@@ -377,6 +387,7 @@ serial_flash: flash@0 {
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <0>;
+		bootph-all;
 	};
 };
 
@@ -386,6 +397,7 @@ &sdhci0 {
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
 	keep-power-in-suspend;
+	bootph-all;
 };
 
 &tscadc0 {
diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
index bc8e1ce11047..6fbd8d932396 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
@@ -171,6 +171,7 @@ vcc_3v3_mmc: regulator-sd {
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
 		regulator-always-on;
+		bootph-all;
 	};
 };
 
@@ -275,6 +276,7 @@ AM64X_IOPAD(0x0290, PIN_INPUT, 0)		/* MMC1_CLKLB */
 			AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0)	/* (J19) MMC1_CMD */
 			AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0)	/* (D19) MMC1_SDCD */
 		>;
+		bootph-all;
 	};
 
 	main_spi0_pins_default: main-spi0-default-pins {
@@ -291,6 +293,7 @@ main_uart0_pins_default: main-uart0-default-pins {
 			AM64X_IOPAD(0x0230, PIN_INPUT, 0)	/* (D15) UART0_RXD */
 			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0)	/* (C16) UART0_TXD */
 		>;
+		bootph-all;
 	};
 
 	main_uart1_pins_default: main-uart1-default-pins {
@@ -413,6 +416,7 @@ &main_uart0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_uart0_pins_default>;
+	bootph-all;
 };
 
 &main_uart1 {
@@ -429,6 +433,7 @@ &sdhci1 {
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	disable-wp;
 	no-1-8-v;
+	bootph-all;
 };
 
 &serdes0 {
-- 
2.34.1