Re: [PATCH v2 3/5] clk: renesas: rzv2h-cpg: Add support for enabling PLLs

[Lad, Prabhakar]

Hi Geert,

On Sun, Mar 9, 2025 at 9:14 PM Prabhakar <prabhakar.csengg@xxxxxxxxx> wrote:
>
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
>
> Some RZ/V2H(P) SoC variants do not have a GPU, resulting in PLLGPU being
> disabled by default in TF-A. Add support for enabling PLL clocks in the
> RZ/V2H(P) CPG driver to manage this.
>
> Introduce `is_enabled` and `enable` callbacks to handle PLL state
> transitions. With the `enable` callback, PLLGPU will be turned ON only
> when the GPU node is enabled; otherwise, it will remain off. Define new
> macros for PLL standby and monitor registers to facilitate this process.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
> v1->v2
> - Updated macros to get PLL offsets
> - Switched to readl_poll_timeout_atomic() and updated the timeout
> ---
>  drivers/clk/renesas/rzv2h-cpg.c | 49 +++++++++++++++++++++++++++++++++
>  1 file changed, 49 insertions(+)
>
> diff --git a/drivers/clk/renesas/rzv2h-cpg.c b/drivers/clk/renesas/rzv2h-cpg.c
> index e489ce28ae63..76ad037b4361 100644
> --- a/drivers/clk/renesas/rzv2h-cpg.c
> +++ b/drivers/clk/renesas/rzv2h-cpg.c
> @@ -44,12 +44,18 @@
>  #define CPG_BUS_1_MSTOP                (0xd00)
>  #define CPG_BUS_MSTOP(m)       (CPG_BUS_1_MSTOP + ((m) - 1) * 4)
>
> +#define CPG_PLL_STBY(x)                ((x))
> +#define CPG_PLL_STBY_RESETB    BIT(0)
> +#define CPG_PLL_STBY_RESETB_WEN        BIT(16)
>  #define CPG_PLL_CLK1(x)                ((x) + 0x004)
>  #define KDIV(val)              ((s16)FIELD_GET(GENMASK(31, 16), (val)))
>  #define MDIV(val)              FIELD_GET(GENMASK(15, 6), (val))
>  #define PDIV(val)              FIELD_GET(GENMASK(5, 0), (val))
>  #define CPG_PLL_CLK2(x)                ((x) + 0x008)
>  #define SDIV(val)              FIELD_GET(GENMASK(2, 0), (val))
> +#define CPG_PLL_MON(x)         ((x) + 0x010)
> +#define CPG_PLL_MON_RESETB     BIT(0)
> +#define CPG_PLL_MON_LOCK       BIT(4)
>
>  #define DDIV_DIVCTL_WEN(shift)         BIT((shift) + 16)
>
> @@ -141,6 +147,47 @@ struct ddiv_clk {
>
>  #define to_ddiv_clock(_div) container_of(_div, struct ddiv_clk, div)
>
> +static int rzv2h_cpg_pll_clk_is_enabled(struct clk_hw *hw)
> +{
> +       struct pll_clk *pll_clk = to_pll(hw);
> +       struct rzv2h_cpg_priv *priv = pll_clk->priv;
> +       u32 val = readl(priv->base + CPG_PLL_MON(pll_clk->pll.offset));
> +
> +       /* Ensure both RESETB and LOCK bits are set */
> +       return (val & (CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK)) ==
> +              (CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK);
> +}
> +
> +static int rzv2h_cpg_pll_clk_enable(struct clk_hw *hw)
> +{
> +       struct pll_clk *pll_clk = to_pll(hw);
> +       struct rzv2h_cpg_priv *priv = pll_clk->priv;
> +       struct pll pll = pll_clk->pll;
> +       u32 stby_offset;
> +       u32 mon_offset;
> +       u32 val;
> +       int ret;
> +
> +       if (rzv2h_cpg_pll_clk_is_enabled(hw))
> +               return 0;
> +
> +       stby_offset = CPG_PLL_STBY(pll.offset);
> +       mon_offset = CPG_PLL_MON(pll.offset);
> +
> +       writel(CPG_PLL_STBY_RESETB_WEN | CPG_PLL_STBY_RESETB,
> +              priv->base + stby_offset);
> +
> +       /* ensure PLL is in normal mode */
> +       ret = readl_poll_timeout_atomic(priv->base + mon_offset, val,
> +                                       (val & (CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK)) ==
> +                                       (CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK), 10, 100);
This timeout didnt work when I power cycled after a complete shutdown overnight.

I will update the timeout as below, this Ive made sure the below delay
works OK after complete shutdown.

/*
* Ensure PLL enters into normal mode
*
* Note: There is no HW information about the worst case latency.
*
* Since this value might be dependent on external xtal rate, pll
* rate or even the other emulation clocks rate, use 2000 as a
* "super" safe value.
*/
ret = readl_poll_timeout_atomic(priv->base + mon_offset, val,
                                                    (val &
(CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK)) ==

(CPG_PLL_MON_RESETB | CPG_PLL_MON_LOCK), 200, 2000);

Please let me know shall I send v3 with this change or wait for your review.

Cheers,
Prabhakar