[PATCH v2 6/8] media: i2c: ov9282: add led_mode v4l2 control
From: Richard Leitner
Date: Fri Mar 14 2025 - 04:51:31 EST
Add V4L2_CID_FLASH_LED_MODE support using the "strobe output enable"
feature of the sensor. This implements following modes:
- V4L2_FLASH_LED_MODE_NONE, which disables the strobe output
- V4L2_FLASH_LED_MODE_FLASH, which enables the strobe output
All values are based on the OV9281 datasheet v1.53 (january 2019) and
tested using an ov9281 VisionComponents module.
Signed-off-by: Richard Leitner <richard.leitner@xxxxxxxxx>
---
drivers/media/i2c/ov9282.c | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
index f42e0d439753e74d14e3a3592029e48f49234927..35edbe1e0efb61a0e03da0ed817c4c4ec0ae9c35 100644
--- a/drivers/media/i2c/ov9282.c
+++ b/drivers/media/i2c/ov9282.c
@@ -670,6 +670,23 @@ static int ov9282_set_ctrl_vflip(struct ov9282 *ov9282, int value)
current_val);
}
+static int ov9282_set_ctrl_flash_led_mode(struct ov9282 *ov9282, int mode)
+{
+ u32 current_val;
+ int ret = ov9282_read_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1,
+ ¤t_val);
+ if (ret)
+ return ret;
+
+ if (mode == V4L2_FLASH_LED_MODE_FLASH)
+ current_val |= OV9282_OUTPUT_ENABLE6_STROBE;
+ else
+ current_val &= ~OV9282_OUTPUT_ENABLE6_STROBE;
+
+ return ov9282_write_reg(ov9282, OV9282_REG_OUTPUT_ENABLE6, 1,
+ current_val);
+}
+
/**
* ov9282_set_ctrl() - Set subdevice control
* @ctrl: pointer to v4l2_ctrl structure
@@ -736,6 +753,9 @@ static int ov9282_set_ctrl(struct v4l2_ctrl *ctrl)
ret = ov9282_write_reg(ov9282, OV9282_REG_TIMING_HTS, 2,
(ctrl->val + ov9282->cur_mode->width) >> 1);
break;
+ case V4L2_CID_FLASH_LED_MODE:
+ ret = ov9282_set_ctrl_flash_led_mode(ov9282, ctrl->val);
+ break;
default:
dev_err(ov9282->dev, "Invalid control %d", ctrl->id);
ret = -EINVAL;
@@ -1391,6 +1411,13 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
OV9282_TIMING_HTS_MAX - mode->width,
1, hblank_min);
+ /* Flash/Strobe controls */
+ v4l2_ctrl_new_std_menu(ctrl_hdlr, &ov9282_ctrl_ops,
+ V4L2_CID_FLASH_LED_MODE,
+ V4L2_FLASH_LED_MODE_TORCH,
+ (1 << V4L2_FLASH_LED_MODE_TORCH),
+ V4L2_FLASH_LED_MODE_NONE);
+
ret = v4l2_fwnode_device_parse(ov9282->dev, &props);
if (!ret) {
/* Failure sets ctrl_hdlr->error, which we check afterwards anyway */
--
2.47.2