Re: [RFC PATCH 1/4] dt-bindings: pinctrl: Add eswin,eic7700-pinctrl binding

[Krzysztof Kozlowski]

On Tue, Mar 25, 2025 at 03:13:03PM +0100, Emil Renner Berthing wrote:
> +properties:
> +  compatible:
> +    enum:
> +      - eswin,eic7700-pinctrl

Blank line

> +  reg:
> +    maxItems: 1
> +
> +required:

required: goes after patternProperties.

> +  - compatible
> +  - reg
> +
> +patternProperties:
> +  '-[0-9]+$':

Recommended is to have more meaningful prefix or suffix, e.g.
-grp/-group. I also don't get why it has to end with number.

> +    type: object
> +    additionalProperties: false
> +
> +    patternProperties:
> +      '-pins$':
> +        type: object
> +        allOf:
> +          - $ref: /schemas/pinctrl/pincfg-node.yaml#
> +          - $ref: /schemas/pinctrl/pinmux-node.yaml#
> +
> +        additionalProperties: false
> +
> +        description:
> +          A pinctrl node should contain at least one subnode describing one
> +          or more pads and their associated pinmux and pinconf settings.
> +
> +        properties:
> +          pins:
> +            items:
> +              enum: [ CHIP_MODE, MODE_SET0, MODE_SET1, MODE_SET2, MODE_SET3,
> +                      XIN, RTC_XIN, RST_OUT_N, KEY_RESET_N, GPIO0, POR_SEL,
> +                      JTAG0_TCK, JTAG0_TMS, JTAG0_TDI, JTAG0_TDO, GPIO5, SPI2_CS0_N,
> +                      JTAG1_TCK, JTAG1_TMS, JTAG1_TDI, JTAG1_TDO, GPIO11, SPI2_CS1_N,
> +                      PCIE_CLKREQ_N, PCIE_WAKE_N, PCIE_PERST_N, HDMI_SCL, HDMI_SDA,
> +                      HDMI_CEC, JTAG2_TRST, RGMII0_CLK_125, RGMII0_TXEN,
> +                      RGMII0_TXCLK, RGMII0_TXD0, RGMII0_TXD1, RGMII0_TXD2,
> +                      RGMII0_TXD3, I2S0_BCLK, I2S0_WCLK, I2S0_SDI, I2S0_SDO,
> +                      I2S_MCLK, RGMII0_RXCLK, RGMII0_RXDV, RGMII0_RXD0, RGMII0_RXD1,
> +                      RGMII0_RXD2, RGMII0_RXD3, I2S2_BCLK, I2S2_WCLK, I2S2_SDI,
> +                      I2S2_SDO, GPIO27, GPIO28, GPIO29, RGMII0_MDC, RGMII0_MDIO,
> +                      RGMII0_INTB, RGMII1_CLK_125, RGMII1_TXEN, RGMII1_TXCLK,
> +                      RGMII1_TXD0, RGMII1_TXD1, RGMII1_TXD2, RGMII1_TXD3, I2S1_BCLK,
> +                      I2S1_WCLK, I2S1_SDI, I2S1_SDO, GPIO34, RGMII1_RXCLK,
> +                      RGMII2_RXDV, RGMII2_RXD0, RGMII2_RXD1, RGMII2_RXD2,
> +                      RGMII2_RXD3, SPI1_CS0_N, SPI1_CLK, SPI1_D0, SPI1_D1, SPI1_D2,
> +                      SPI1_D3, SPI1_CS1_N, RGMII1_MDC, RGMII1_MDIO, RGMII1_INTB,
> +                      USB0_PWREN, USB1_PWREN, I2C0_SCL, I2C0_SDA, I2C1_SCL, I2C1_SDA,
> +                      I2C2_SCL, I2C2_SDA, I2C3_SCL, I2C3_SDA, I2C4_SCL, I2C4_SDA,
> +                      I2C5_SCL, I2C5_SDA, UART0_TX, UART0_RX, UART1_TX, UART1_RX,
> +                      UART1_CTS, UART1_RTS, UART2_TX, UART2_RX, JTAG2_TCK, JTAG2_TMS,
> +                      JTAG2_TDI, JTAG2_TDO, FAN_PWM, FAN_TACH, MIPI_CSI0_XVS,
> +                      MIPI_CSI0_XHS, MIPI_CSI0_MCLK, MIPI_CSI1_XVS, MIPI_CSI1_XHS,
> +                      MIPI_CSI1_MCLK, MIPI_CSI2_XVS, MIPI_CSI2_XHS, MIPI_CSI2_MCLK,
> +                      MIPI_CSI3_XVS, MIPI_CSI3_XHS, MIPI_CSI3_MCLK, MIPI_CSI4_XVS,
> +                      MIPI_CSI4_XHS, MIPI_CSI4_MCLK, MIPI_CSI5_XVS, MIPI_CSI5_XHS,
> +                      MIPI_CSI5_MCLK, SPI3_CS_N, SPI3_CLK, SPI3_DI, SPI3_DO, GPIO92,
> +                      GPIO93, S_MODE, GPIO95, SPI0_CS_N, SPI0_CLK, SPI0_D0, SPI0_D1,
> +                      SPI0_D2, SPI0_D3, I2C10_SCL, I2C10_SDA, I2C11_SCL, I2C11_SDA,
> +                      GPIO106, BOOT_SEL0, BOOT_SEL1, BOOT_SEL2, BOOT_SEL3, GPIO111,
> +                      LPDDR_REF_CLK ]

All these should be lowercase.

> +            description: List of pads that properties in the node apply to.
> +
> +          function:
> +            enum: [ csi, debug, ddr, fan, gpio, hdmi, i2c, i2s, jtag, mipi,
> +                    mode, oscillator, pci, pwm, rgmii, reset, sata, spi, sdio,
> +                    uart, usb ]
> +            description: The mux function to select for the given pins.
> +
> +          bias-disable: true
> +
> +          bias-pull-up:
> +            oneOf:
> +              - type: boolean
> +              - const: 25000
> +            description: Enable internal 25kOhm pull-up

Why bool and fixed value? Do they have different meaning? Description
says they are the same.

Anyway, don't repeat constraints in free form text.

> +
> +          bias-pull-down:
> +            oneOf:
> +              - type: boolean
> +              - const: 22000
> +            description: Enable internal 22kOhm pull-down

Same questions

> +
> +          drive-strength-microamp:
> +            enum: [ 3100, 6700, 9600, 12900, 18000, 20900, 23200, 25900 ]
> +
> +          input-enable: true
> +
> +          input-disable: true
> +
> +          input-schmitt-enable: true
> +
> +          input-schmitt-disable: true
> +
> +        required:
> +          - pins

Best regards,
Krzysztof