[PATCH v2 3/4] ARM: dts: nxp: mxs: Adjust XEA board's DTS to support L2 switch

[Lukasz Majewski]

The description is similar to the one used with the new CPSW driver.

Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
---
Changes for v2:
- Remove properties which are common for the imx28(7) SoC
- Use mdio properties to perform L2 switch reset (avoid using
  deprecated properties)
---
 arch/arm/boot/dts/nxp/mxs/imx28-xea.dts | 54 +++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
index 6c5e6856648a..d5558e24844c 100644
--- a/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
@@ -5,6 +5,7 @@
  */
 
 /dts-v1/;
+#include<dt-bindings/interrupt-controller/irq.h>
 #include "imx28-lwe.dtsi"
 
 / {
@@ -90,6 +91,59 @@ &reg_usb_5v {
 	gpio = <&gpio0 2 0>;
 };
 
+&eth_switch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac1_pins_a>;
+	phy-supply = <&reg_fec_3v3>;
+	status = "okay";
+
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mtip_port1: port@1 {
+			reg = <1>;
+			label = "lan0";
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-mode = "rmii";
+			phy-handle = <&ethphy0>;
+		};
+
+		mtip_port2: port@2 {
+			reg = <2>;
+			label = "lan1";
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-mode = "rmii";
+			phy-handle = <&ethphy1>;
+		};
+	};
+
+	mdio_sw: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio3 21 0>;
+		reset-delay-us = <25000>;
+		reset-post-delay-us = <10000>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			smsc,disable-energy-detect;
+			/* Both PHYs (i.e. 0,1) have the same, single GPIO, */
+			/* line to handle both, their interrupts (AND'ed) */
+			interrupt-parent = <&gpio4>;
+			interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			smsc,disable-energy-detect;
+			interrupt-parent = <&gpio4>;
+			interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
 &spi2_pins_a {
 	fsl,pinmux-ids = <
 		MX28_PAD_SSP2_SCK__SSP2_SCK
-- 
2.39.5