Re: [PATCH v2 3/3] media: imx-jpeg: Check decoding is ongoing for motion-jpeg

From: Ming Qian(OSS)
Date: Sun Mar 30 2025 - 23:10:47 EST



Hi Frank,

On 2025/3/28 22:45, Frank Li wrote:
On Fri, Mar 28, 2025 at 02:30:52PM +0800, ming.qian@xxxxxxxxxxx wrote:
From: Ming Qian <ming.qian@xxxxxxxxxxx>

To support decoding motion-jpeg without DHT, driver will try to decode a
pattern jpeg before actual jpeg frame by use of linked descriptors
(This is called "repeat mode"), then the DHT in the pattern jpeg can be
used for decoding the motion-jpeg.

In other words, 2 frame done interrupts will be triggered, driver will
ignore the first interrupt,

Does any field in linked descriptors to control if issue irq? Generally
you needn't enable first descriptors's irq and only enable second one.


Unfortunately, we cannot configure interrupts for each descriptor.
So we can't only enable the second irq.


and wait for the second interrupt.
If the resolution is small, and the 2 interrupts may be too close,

It also possible two irqs combine to 1 irqs. If I understand correct, your
irq handle only handle one descriptors per irq.

Another words,

If second irq already happen just before 1,

1. dec_ret = readl(reg + MXC_SLOT_OFFSET(slot, SLOT_STATUS));
2. writel(dec_ret, reg + MXC_SLOT_OFFSET(slot, SLOT_STATUS)); /* w1c */

Does your driver wait forever because no second irq happen?

Frank

Before this patch, the answer is yes, the driver will wait 2 seconds
until timeout.
In fact, this is the problem that this patch wants to avoid.
Now I think there are 3 cases for motion-jpeg decoding:
1. The second irq happens before the first irq status check, the on-going check
help to hanle this case.
2. The second irq happens after the first irq status check, but before
on-going check, this on-going check can help handle it, fisnish the
current decoding and reset the jpeg decoder.
3. The second irq happens after the on-going check, this is the normal
process before. No additional processing required.

Thanks,
Ming


when driver is handling the first interrupt, two frames are done, then
driver will fail to wait for the second interrupt.

In such case, driver can check whether the decoding is still ongoing,
if not, just done the current decoding.

Signed-off-by: Ming Qian <ming.qian@xxxxxxxxxxx>
---
.../media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h | 1 +
.../media/platform/nxp/imx-jpeg/mxc-jpeg.c | 20 ++++++++++++++++++-
2 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h b/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h
index d579c804b047..adb93e977be9 100644
--- a/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h
+++ b/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg-hw.h
@@ -89,6 +89,7 @@
/* SLOT_STATUS fields for slots 0..3 */
#define SLOT_STATUS_FRMDONE (0x1 << 3)
#define SLOT_STATUS_ENC_CONFIG_ERR (0x1 << 8)
+#define SLOT_STATUS_ONGOING (0x1 << 31)

/* SLOT_IRQ_EN fields TBD */

diff --git a/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c b/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c
index 45705c606769..e6bb45633a19 100644
--- a/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c
+++ b/drivers/media/platform/nxp/imx-jpeg/mxc-jpeg.c
@@ -910,6 +910,23 @@ static u32 mxc_jpeg_get_plane_size(struct mxc_jpeg_q_data *q_data, u32 plane_no)
return size;
}

+static bool mxc_dec_is_ongoing(struct mxc_jpeg_ctx *ctx)
+{
+ struct mxc_jpeg_dev *jpeg = ctx->mxc_jpeg;
+ u32 curr_desc;
+ u32 slot_status;
+
+ slot_status = readl(jpeg->base_reg + MXC_SLOT_OFFSET(ctx->slot, SLOT_STATUS));
+ curr_desc = readl(jpeg->base_reg + MXC_SLOT_OFFSET(ctx->slot, SLOT_CUR_DESCPT_PTR));
+
+ if (curr_desc == jpeg->slot_data.cfg_desc_handle)
+ return true;
+ if (slot_status & SLOT_STATUS_ONGOING)
+ return true;
+
+ return false;
+}
+
static irqreturn_t mxc_jpeg_dec_irq(int irq, void *priv)
{
struct mxc_jpeg_dev *jpeg = priv;
@@ -979,7 +996,8 @@ static irqreturn_t mxc_jpeg_dec_irq(int irq, void *priv)
mxc_jpeg_enc_mode_go(dev, reg, mxc_jpeg_is_extended_sequential(q_data->fmt));
goto job_unlock;
}
- if (jpeg->mode == MXC_JPEG_DECODE && jpeg_src_buf->dht_needed) {
+ if (jpeg->mode == MXC_JPEG_DECODE && jpeg_src_buf->dht_needed &&
+ mxc_dec_is_ongoing(ctx)) {
jpeg_src_buf->dht_needed = false;
dev_dbg(dev, "Decoder DHT cfg finished. Start decoding...\n");
goto job_unlock;
--
2.43.0-rc1