Re: [PATCH v6 1/2] arm64: dts: qcom: ipq5424: Add PCIe PHYs and controller nodes

[Manikanta Mylavarapu]

On 4/14/2025 4:17 PM, Konrad Dybcio wrote:
> On 4/2/25 12:27 PM, Manikanta Mylavarapu wrote:
>> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
>> found on IPQ5424 platform. The PCIe0 & PCIe1 are 1-lane Gen3
>> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>>
>> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@xxxxxxxxxxx>
>> ---
> 
> [...]
> 
>> +		pcie0_phy: phy@84000 {
>> +			compatible = "qcom,ipq5424-qmp-gen3x1-pcie-phy",
>> +				     "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> +			reg = <0x0 0x00084000 0x0 0x2000>;
> 
> This is 0x1000-wide
> 

Okay, sure.

>> +			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
>> +				 <&gcc GCC_PCIE0_AHB_CLK>,
>> +				 <&gcc GCC_PCIE0_PIPE_CLK>;
>> +			clock-names = "aux",
>> +				      "cfg_ahb",
>> +				      "pipe";
>> +
>> +			assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
>> +			assigned-clock-rates = <20000000>;
>> +
>> +			resets = <&gcc GCC_PCIE0_PHY_BCR>,
>> +				 <&gcc GCC_PCIE0PHY_PHY_BCR>;
>> +			reset-names = "phy",
>> +				      "common";
>> +
>> +			#clock-cells = <0>;
>> +			clock-output-names = "gcc_pcie0_pipe_clk_src";
>> +
>> +			#phy-cells = <0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pcie1_phy: phy@8c000 {
>> +			compatible = "qcom,ipq5424-qmp-gen3x1-pcie-phy",
>> +				     "qcom,ipq9574-qmp-gen3x1-pcie-phy";
>> +			reg = <0x0 0x0008c000 0x0 0x2000>;
> 
> So is this
> 

Okay, sure.

>> +			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
>> +				 <&gcc GCC_PCIE1_AHB_CLK>,
>> +				 <&gcc GCC_PCIE1_PIPE_CLK>;
>> +			clock-names = "aux",
>> +				      "cfg_ahb",
>> +				      "pipe";
>> +
>> +			assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
>> +			assigned-clock-rates = <20000000>;
>> +
>> +			resets = <&gcc GCC_PCIE1_PHY_BCR>,
>> +				 <&gcc GCC_PCIE1PHY_PHY_BCR>;
>> +			reset-names = "phy",
>> +				      "common";
>> +
>> +			#clock-cells = <0>;
>> +			clock-output-names = "gcc_pcie1_pipe_clk_src";
>> +
>> +			#phy-cells = <0>;
>> +			status = "disabled";
>> +		};
> 
> 
>> +		pcie3: pcie@40000000 {
>> +			compatible = "qcom,pcie-ipq5424", "qcom,pcie-ipq9574";
>> +			reg = <0x0 0x40000000 0x0 0xf1c>,
>> +			      <0x0 0x40000f20 0x0 0xa8>,
>> +			      <0x0 0x40001000 0x0 0x1000>,
>> +			      <0x0 0x000f8000 0x0 0x3000>,
>> +			      <0x0 0x40100000 0x0 0x1000>,
>> +			      <0x0 0x000fe000 0x0 0x1000>;
>> +			reg-names = "dbi",
>> +				    "elbi",
>> +				    "atu",
>> +				    "parf",
>> +				    "config",
>> +				    "mhi";
>> +			device_type = "pci";
>> +			linux,pci-domain = <3>;
>> +			num-lanes = <2>;
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +
>> +			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x00100000>,
>> +				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x0fd00000>;
> 
> I think the BAR spaces on all these hosts are only 32 MiB long
> 

I have confirmed with the hardware team that the specified BAR register space is accurate.
256MB for all PCIe controllers.

Thanks & Regards,
Manikanta.