RE: [PATCH v3 3/3] arm64: dts: renesas: rzg3e-smarc-som: Enable eth{0-1} (GBETH) interfaces

[Biju Das]

> -----Original Message-----
> From: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
> Sent: 25 June 2025 16:17
> Subject: Re: [PATCH v3 3/3] arm64: dts: renesas: rzg3e-smarc-som: Enable eth{0-1} (GBETH) interfaces
> 
> Hi John,
> 
> On Mon, 23 Jun 2025 at 10:04, John Madieu <john.madieu.xa@xxxxxxxxxxxxxx> wrote:
> > Enable the Gigabit Ethernet Interfaces (GBETH) populated on the RZ/G3E
> > SMARC EVK
> >
> > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > Tested-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
> > Reviewed-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
> > Signed-off-by: John Madieu <john.madieu.xa@xxxxxxxxxxxxxx>
> 
> > v3:
> > Updates mdio separately, based on phandles instead of node
> > redefinition
> 
> Thanks for the update!
> 
> > --- a/arch/arm64/boot/dts/renesas/rzg3e-smarc-som.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/rzg3e-smarc-som.dtsi
> 
> >  &pinctrl {
> > +       eth0_pins: eth0 {
> > +               pinmux = <RZG3E_PORT_PINMUX(A, 1, 1)>, /* MDC */
> > +                        <RZG3E_PORT_PINMUX(A, 0, 1)>, /* MDIO */
> > +                        <RZG3E_PORT_PINMUX(C, 2, 15)>, /* PHY_INTR (IRQ2) */
> > +                        <RZG3E_PORT_PINMUX(C, 1, 1)>, /* RXD3 */
> > +                        <RZG3E_PORT_PINMUX(C, 0, 1)>, /* RXD2 */
> > +                        <RZG3E_PORT_PINMUX(B, 7, 1)>, /* RXD1 */
> > +                        <RZG3E_PORT_PINMUX(B, 6, 1)>, /* RXD0 */
> > +                        <RZG3E_PORT_PINMUX(B, 0, 1)>, /* RXC */
> > +                        <RZG3E_PORT_PINMUX(A, 2, 1)>, /* RX_CTL */
> > +                        <RZG3E_PORT_PINMUX(B, 5, 1)>, /* TXD3 */
> > +                        <RZG3E_PORT_PINMUX(B, 4, 1)>, /* TXD2 */
> > +                        <RZG3E_PORT_PINMUX(B, 3, 1)>, /* TXD1 */
> > +                        <RZG3E_PORT_PINMUX(B, 2, 1)>, /* TXD0 */
> > +                        <RZG3E_PORT_PINMUX(B, 1, 1)>, /* TXC */
> > +                        <RZG3E_PORT_PINMUX(A, 3, 1)>; /* TX_CTL */
> > +       };
> > +
> > +       eth1_pins: eth1 {
> > +               pinmux = <RZG3E_PORT_PINMUX(D, 1, 1)>, /* MDC */
> > +                        <RZG3E_PORT_PINMUX(D, 0, 1)>, /* MDIO */
> > +                        <RZG3E_PORT_PINMUX(F, 2, 15)>, /* PHY_INTR (IRQ15) */
> > +                        <RZG3E_PORT_PINMUX(F, 1, 1)>, /* RXD3 */
> > +                        <RZG3E_PORT_PINMUX(F, 0, 1)>, /* RXD2 */
> > +                        <RZG3E_PORT_PINMUX(E, 7, 1)>, /* RXD1 */
> > +                        <RZG3E_PORT_PINMUX(E, 6, 1)>, /* RXD0 */
> > +                        <RZG3E_PORT_PINMUX(E, 0, 1)>, /* RXC */
> > +                        <RZG3E_PORT_PINMUX(D, 2, 1)>, /* RX_CTL */
> > +                        <RZG3E_PORT_PINMUX(E, 5, 1)>, /* TXD3 */
> > +                        <RZG3E_PORT_PINMUX(E, 4, 1)>, /* TXD2 */
> > +                        <RZG3E_PORT_PINMUX(E, 3, 1)>, /* TXD1 */
> > +                        <RZG3E_PORT_PINMUX(E, 2, 1)>, /* TXD0 */
> > +                        <RZG3E_PORT_PINMUX(E, 1, 1)>, /* TXC */
> > +                        <RZG3E_PORT_PINMUX(D, 3, 1)>; /* TX_CTL */
> > +       };
> > +
> >         i2c2_pins: i2c {
> >                 pinmux = <RZG3E_PORT_PINMUX(3, 4, 1)>, /* SCL2 */
> >                          <RZG3E_PORT_PINMUX(3, 5, 1)>; /* SDA2 */
> 
> Based on the feedback from Prabhakar on v2, I understand this needs to configure output-enable for the
> ET0_TXC_TXCLK and ET1_TXC_TXCLK pins, and to add support for that in the pin control driver first?
> 
> [1] https://lore.kernel.org/all/CA+V-a8uizu5MCur_=g5vJyWbWSTSP2J6FkQ89JB8ges7GWdsjg@xxxxxxxxxxxxxx/

Maybe this could be the reason for RZ/V2H sees clock monitor issue during unbind/bind and RZ/G3E don't see it when
using DEF_MOD macro. Maybe after this change, It may trigger the clock monitor issue on RZ/G3E as well
forcing to use DEF_MOD_EXTERNAL??

Cheers,
Biju