Re: [PATCH v2] arm64: dts: qcom: Add initial audio support for Hamoa-IOT-EVK

[Alexey Klimov]

On Mon Jul 28, 2025 at 8:16 AM BST, leqi via B4 Relay wrote:
> From: leqi <leqi@xxxxxxxxxxxxxxxx>
>
> This patch adds initial audio codec support for the Hamoa-IOT-EVK board,
> including WCD9385 configuration, micbias voltage settings, GPIO reset,
> and power supply bindings. It enables basic audio functionality for
> further development. Basic test is good in Hamoa-IOT-EVK board.
>
> Signed-off-by: leqi <leqi@xxxxxxxxxxxxxxxx>
> ---
> Changes in v2:
> - Updated author email address to leqi@xxxxxxxxxxxxxxxx.
> - Clarified that audio is validated with this change.
> - Link to v1: https://lore.kernel.org/all/20250723-initial_audio_support_for_qualcomm_hamoa_iot_evk_board-v1-1-816991701952@xxxxxxxxxxx/
> ---
>  arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 232 +++++++++++++++++++++++++++++
>  1 file changed, 232 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> index 843f39c9d59286a9303a545411b2518d7649a059..91618e22e86c46c698b3639f60bc19314705b391 100644
> --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> @@ -124,6 +124,94 @@ pmic_glink_ss2_con_sbu_in: endpoint {
>  		};
>  	};
>  
> +	sound {
> +		compatible = "qcom,x1e80100-sndcard";
> +		model = "X1E80100-EVK";
> +		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
> +				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
> +				"WooferRight IN", "WSA2 WSA_SPK2 OUT",
> +				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",

Could you please check/confirm that above routing path
"WooferRight IN" -> "WSA2 WSA_SPK2 OUT" is correct?

Left path get input from both WSA_SPK{1,2} while the right one only uses
WSA_SPK2.


> +				"IN1_HPHL", "HPHL_OUT",
> +				"IN2_HPHR", "HPHR_OUT",
> +				"AMIC2", "MIC BIAS2",
> +				"VA DMIC0", "MIC BIAS3",
> +				"VA DMIC1", "MIC BIAS3",
> +				"VA DMIC2", "MIC BIAS1",
> +				"VA DMIC3", "MIC BIAS1",
> +				"VA DMIC0", "VA MIC BIAS3",
> +				"VA DMIC1", "VA MIC BIAS3",
> +				"VA DMIC2", "VA MIC BIAS1",
> +				"VA DMIC3", "VA MIC BIAS1",
> +				"TX SWR_INPUT1", "ADC2_OUTPUT";
> +
> +		wcd-playback-dai-link {
> +			link-name = "WCD Playback";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> +			};
> +
> +			codec {
> +				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};

Please sort subnodes alphabetically here and below.

> +		wcd-capture-dai-link {
> +			link-name = "WCD Capture";
> +
> +			cpu {
> +				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
> +			};
> +
> +			codec {
> +				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
> +			};
> +
> +			platform {
> +				sound-dai = <&q6apm>;
> +			};
> +		};
> +

[...]

Best regards,
Alexey