Re: [PATCH v10 3/3] arm64: dts: qcom: sm8750: Add USB support for SM8750 MTP platform

[Krishna Kurapati PSSNV]

On 10/31/2025 8:14 PM, Dmitry Baryshkov wrote:
> On Fri, Oct 31, 2025 at 06:03:54PM +0530, Krishna Kurapati wrote:
> > From: Wesley Cheng <wesley.cheng@xxxxxxxxxxxxxxxx>
> >
> > Enable USB support on SM8750 QRD variant. Add the PMIC glink node with
> > connector to enable role switch support.
>
> Subject speaks about MTP.

My bad. Will fix it up.

Regards,
Krishna,

> > Signed-off-by: Wesley Cheng <wesley.cheng@xxxxxxxxxxxxxxxx>
> > [Konrad: Provided diff to flatten USB node on MTP]
> > Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxxxx>
> > Co-developed-by: Jishnu Prakash <jishnu.prakash@xxxxxxxxxxxxxxxx>
> > Signed-off-by: Jishnu Prakash <jishnu.prakash@xxxxxxxxxxxxxxxx>
> > Signed-off-by: Krishna Kurapati <krishna.kurapati@xxxxxxxxxxxxxxxx>
> > ---
> >   arch/arm64/boot/dts/qcom/sm8750-qrd.dts | 73 +++++++++++++++++++++++++
> >   1 file changed, 73 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
> > index 13c7b9664c89..c545695751db 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
> > +++ b/arch/arm64/boot/dts/qcom/sm8750-qrd.dts
> > @@ -193,6 +193,51 @@ platform {
> >   		};
> >   	};
> >   
> > +	pmic-glink {
> > +		compatible = "qcom,sm8750-pmic-glink",
> > +			     "qcom,sm8550-pmic-glink",
> > +			     "qcom,pmic-glink";
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		orientation-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
> > +
> > +		connector@0 {
> > +			compatible = "usb-c-connector";
> > +			reg = <0>;
> > +
> > +			power-role = "dual";
> > +			data-role = "dual";
> > +
> > +			ports {
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				port@0 {
> > +					reg = <0>;
> > +
> > +					pmic_glink_hs_in: endpoint {
> > +						remote-endpoint = <&usb_dwc3_hs>;
> > +					};
> > +				};
> > +
> > +				port@1 {
> > +					reg = <1>;
> > +
> > +					pmic_glink_ss_in: endpoint {
> > +						remote-endpoint = <&usb_dp_qmpphy_out>;
> > +					};
> > +				};
> > +
> > +				port@2 {
> > +					reg = <2>;
> > +
> > +					pmic_glink_sbu: endpoint {
> > +					};
> > +				};
> > +			};
> > +		};
> > +	};
> > +
> >   	vph_pwr: vph-pwr-regulator {
> >   		compatible = "regulator-fixed";
> >   
> > @@ -1054,3 +1099,31 @@ &ufs_mem_hc {
> >   
> >   	status = "okay";
> >   };
> > +
> > +&usb {
> > +	status = "okay";
> > +};
> > +
> > +&usb_dwc3_hs {
> > +	remote-endpoint = <&pmic_glink_hs_in>;
> > +};
> > +
> > +&usb_hsphy {
> > +	vdd-supply = <&vreg_l2d_0p88>;
> > +	vdda12-supply = <&vreg_l3g_1p2>;
> > +
> > +	phys = <&pmih0108_eusb2_repeater>;
> > +
> > +	status = "okay";
> > +};
> > +
> > +&usb_dp_qmpphy {
> > +	vdda-phy-supply = <&vreg_l3g_1p2>;
> > +	vdda-pll-supply = <&vreg_l2d_0p88>;
> > +
> > +	status = "okay";
> > +};
> > +
> > +&usb_dp_qmpphy_out {
> > +	remote-endpoint = <&pmic_glink_ss_in>;
> > +};
>
> usb_dp < usb_hsphy
>
> > --
> > 2.34.1