Re: [PATCH] arm64: dts: rockchip: align bindings to PCIe spec

[Shawn Lin]

Hi Geraldo,

在 2025/11/05 星期三 13:55, Geraldo Nascimento 写道:
> The PERST# side-band signal is defined by PCIe spec as an open-drain

I couldn't find any clue that says PERST# is an open-drain signal. Could
you quote it from PCI Express Card Electromechanical Specification?

> active-low signal that depends on a pull-up resistor to keep the
> signal high when deasserted. Align bindings to the spec.

This is not true from my POV. An open-drain PCIe side-band  signal
is used for both of EP and RC to achieve some special work-flow, like
CLKREQ# for L1ss, etc. Since both ends could control it. But PERST# is a
fundamental reset signal driven by RC which should be in sure state,
high or low, has nothing to do with open-drain.

> Note that the relevant driver hacks the active-low signal as
> active-high and switches the normal polarity of PERST#
> assertion/deassertion, 1 and 0 in that order, and instead uses
> 0 to signal low (assertion) and 1 to signal deassertion.
>
> Incidentally, this change makes hardware that refused to work
> with the Rockchip-IP PCIe core working for me, which was the
> object of many fool's errands.
>
> Signed-off-by: Geraldo Nascimento <geraldogabriel@xxxxxxxxx>
> ---
>   arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi | 8 ++++++--
>   1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
> index aa70776e898a..8dcb03708145 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
> @@ -383,9 +383,9 @@ &pcie_phy {
>   };
>   
>   &pcie0 {
> -	ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
> +	ep-gpios = <&gpio0 RK_PB4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;

So my biggest guess is we don't need this change at all.
gpio0b4 is used as gpio function, the problem you faced is that it
didn't set gpio0b4 as pull-up, because the defaut state is pull-down.

Maybe the drive current of this IO is too weak, making it unable to 
fully drive high in the pull-down state? If that's the case, can you see 
a half-level signal on the oscilloscope?

>   	num-lanes = <4>;
> -	pinctrl-0 = <&pcie_clkreqnb_cpm>;
> +	pinctrl-0 = <&pcie_clkreqnb_cpm>, <&pcie_perst>;
>   	pinctrl-names = "default";
>   	vpcie0v9-supply = <&vcca_0v9>;	/* VCC_0V9_S0 */
>   	vpcie1v8-supply = <&vcca_1v8>;	/* VCC_1V8_S0 */
> @@ -408,6 +408,10 @@ pcie {
>   		pcie_pwr: pcie-pwr {
>   			rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
>   		};
> +		pcie_perst: pcie-perst {
> +			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +
>   	};
>   
>   	pmic {