[PATCH] arm64: dts: qcom: monaco-evk: Enable PCIe0 and PCIe1 on monaco-evk

[Sushrut Shree Trivedi]

Enables PCIe0 and PCIe1 controller and phy-nodes.

PCIe0 is routed to an m.2 E key connector on the mainboard for wifi
attaches while PCIe1 routes to a standard PCIe x4 expansion slot.

Signed-off-by: Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>
---
This patch depends on the series:
https://lore.kernel.org/all/20251024095609.48096-1-ziyue.zhang@xxxxxxxxxxxxxxxx/
---
 arch/arm64/boot/dts/qcom/monaco-evk.dts | 84 +++++++++++++++++++++++++++++++++
 1 file changed, 84 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/monaco-evk.dts b/arch/arm64/boot/dts/qcom/monaco-evk.dts
index e72cf6725a52..70739f71dd5c 100644
--- a/arch/arm64/boot/dts/qcom/monaco-evk.dts
+++ b/arch/arm64/boot/dts/qcom/monaco-evk.dts
@@ -408,6 +408,44 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+&pcie0 {
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcieport0 {
+	reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l6a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcieport1 {
+	reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l6a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
 &remoteproc_adsp {
 	firmware-name = "qcom/qcs8300/adsp.mbn";
 
@@ -449,6 +487,52 @@ ethernet0_mdio: ethernet0-mdio-pins {
 		};
 	};
 
+	pcie0_default_state: pcie0-default-state {
+		wake-pins {
+			pins = "gpio0";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		clkreq-pins {
+			pins = "gpio1";
+			function = "pcie0_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio2";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	pcie1_default_state: pcie1-default-state {
+		wake-pins {
+			pins = "gpio21";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		clkreq-pins {
+			pins = "gpio22";
+			function = "pcie1_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-pins {
+			pins = "gpio23";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
 	qup_i2c1_default: qup-i2c1-state {
 		pins = "gpio19", "gpio20";
 		function = "qup0_se1";

---
base-commit: b89214826b1ab0e527303464d6c90e53d290c4f1
change-id: 20251110-monaco-evk-pci-85c9459ce9a2

Best regards,
-- 
Sushrut Shree Trivedi <quic_sushruts@xxxxxxxxxxx>