Re: [PATCH v3 8/8] arm64: dts: qcom: Add support for Pixel 3 and Pixel 3 XL

[Konrad Dybcio]

On 11/18/25 12:30 PM, David Heidelberg via B4 Relay wrote:
> From: David Heidelberg <david@xxxxxxx>
> 
> This adds initial device tree support for the following phones:
> 
>  - Google Pixel 3 (blueline)
>  - Google Pixel 3 XL (crosshatch)
> 
> Both phone boards use the same identifiers and differ only slightly
> in their connected peripherals.

[...]

> +&cont_splash_mem {
> +	reg = <0 0x9d400000 0 0x02400000>;
> +};

You override it to the same value on both devices, keep it in common

> +
> +&framebuffer0 {
> +	width = <1080>;
> +	height = <2160>;
> +	stride = <(1080 * 4)>;
> +	format = "a8r8g8b8";

The format is mandated by the UEFI specification and won't change too

[...]

> +&tlmm {
> +	panel_te_pin: panel-te-state {
> +		pins = "gpio12";
> +		function = "mdp_vsync";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	panel_reset_pins: panel-active-state {
> +		pins = "gpio6";

Pin entries would be best sorted by the GPIO index:

https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-nodes


> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +	};
> +
> +	panel_suspend: panel-suspend-state {
> +		pins = "gpio6";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +};

Stray \n above

[...]

> +&adsp_pas {
> +	firmware-name = "qcom/sdm845/Google/blueline/adsp.mbn";

Sorry if I asked this before, but are the binaries identical for
both devices?

[...]


> +		vreg_l14a_1p88: ldo14 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-boot-on;
> +			/*
> +			 * We can't properly bring the panel back if it gets turned off
> +			 * so keep it's regulators always on for now.
> +			 */
> +			regulator-always-on;

Is that still the case with your fixes to the panel driver?

[...]

> +
> +		vreg_l28a_3p0: ldo28 {
> +			regulator-min-microvolt = <2856000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> +			regulator-boot-on;
> +			/*
> +			 * We can't properly bring the panel back if it gets turned off
> +			 * so keep it's regulators always on for now.
> +			 */
> +			regulator-always-on;

ditto

[...]

> +	regulators-1 {
> +		compatible = "qcom,pmi8998-rpmh-regulators";
> +		qcom,pmic-id = "b";
> +
> +		vdd-bob-supply = <&vph_pwr>;
> +
> +		vreg_bob: bob {
> +			regulator-min-microvolt = <3312000>;
> +			regulator-max-microvolt = <3600000>;

This is a very broad range, what voltage does it need to be?

[...]

[...]

> +&tlmm {
> +	gpio-reserved-ranges = < 0 4>, /* SPI (Intel MNH Pixel Visual Core) */

stray space before '0'

Konrad