Re: [PATCH v3 7/7] dt-bindings: iio: adc: adi,ad4030: add data-lanes property

[Marcelo Schmitt]

On 12/04, Rob Herring wrote:
> On Mon, Dec 01, 2025 at 08:20:45PM -0600, David Lechner wrote:
> > Add data-lanes property to specify the number of data lanes used on the
> > ad463x chips that support reading two samples at the same time using
> > two data lanes with a capable SPI controller.
> > 
> > Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
> > ---
> > v3 changes: new patch
> > 
> > I added this one to give a real-world use case where spi-rx-bus-width
> > was not sufficient to fully describe the hardware configuration.
> > 
> > spi-rx-bus-width = <4>; alone could be be interpreted as either:
> > 
> > +--------------+    +----------+
> > | SPI          |    | AD4630   |
> > | Controller   |    | ADC      |
> > |              |    |          |
> > |        SDIA0 |<---| SDOA0    |
> > |        SDIA1 |<---| SDOA1    |
> > |        SDIA2 |<---| SDOA2    |
> > |        SDIA3 |<---| SDOA3    |
> > |              |    |          |
> > |        SDIB0 |x   | SDOB0    |
> > |        SDIB1 |x   | SDOB1    |
> > |        SDIB2 |x   | SDOB2    |
> > |        SDIB3 |x   | SDOB3    |
> > |              |    |          |
> > +--------------+     +---------+
> > 
> > or
> > 
> > +--------------+    +----------+
> > | SPI          |    | AD4630   |
> > | Controller   |    | ADC      |
> > |              |    |          |
> > |        SDIA0 |<---| SDOA0    |
> > |        SDIA1 |<---| SDOA1    |
> > |        SDIA2 |x   | SDOA2    |
> > |        SDIA3 |x   | SDOA3    |
> > |              |    |          |
> > |        SDIB0 |<---| SDOB0    |
> > |        SDIB1 |<---| SDOB1    |
> > |        SDIB2 |x   | SDOB2    |
> > |        SDIB3 |x   | SDOB3    |
> > |              |    |          |
> > +--------------+     +---------+
> > 
> > Now, with data-lanes having a default value of [0] (inherited from
> > spi-peripheral-props.yaml), specifying:
> > 
> >     spi-rx-bus-width = <4>;
> > 
> > is unambiguously the first case and the example given in the binding
> > documentation is the second case:
> > 
> >     spi-rx-bus-width = <2>;
> >     data-lanes = <0>, <1>;
> 
> I just reviewed this and all, but what if you just did:
> 
> spi-rx-bus-width = <2>, <2>;
> 
> So *-bus-width becomes equal to the number of serializers/channels.

Unless I'm missing something, I think that would also describe the currently
possible use cases as well. To me, it actually seems even more accurate than
data-lanes. The data-lanes property only describes the SPI controller input
lines/lanes, no info is given about the output lanes. Well yeah, that would only
be a problem for a device with multiple input serializers and multiple output
serializers. Still, the *-bus-width = <N>, <N>, ... <N>; notation looks clearer,
IMHO.

> 
> Rob
>