Re: [PATCH RFC RFT] interconnect: qcom: implement get_bw with rpmh_read

[Neil Armstrong]

On 1/14/26 11:31, Konrad Dybcio wrote:
> On 1/14/26 11:07 AM, Neil Armstrong wrote:
> > On 1/14/26 11:01, Konrad Dybcio wrote:
> > > On 1/13/26 6:53 PM, Georgi Djakov wrote:
> > > > On 11/6/25 6:46 PM, Neil Armstrong wrote:
> > > > > Since we can actually read back the APPS rpmh interconnect
> > > > > BCM votes we can actually implement the get_bw() callback
> > > > > and provide a coherent average and peak bandwidth at probe time.
> > > > >
> > > > > The benefits of that are:
> > > > > - keep disabled BCMs disabled
> > > > > - avoid voting unused BCMs to INT_MAX
> > > > >
> > > > > If the interconnects are correctly described for a platform,
> > > > > all the required BCMs would be voted to the maximum bandwidth
> > > > > until sync_state is reached.
> > > > >
> > > > > Since we only get the BCM vote, we need to redistribute
> > > > > the vote values to the associated nodes. The initial BCM
> > > > > votes are read back at probe time in order to be ready when
> > > > > the get_bw() is called when a node is added.
> > > >
> > > > FWIW, I was able to finally test this on sdm845. Some nodes are indeed
> > > > showing reasonable bandwidth values instead of the default INT_MAX.
> > >
> > > As I learnt here
> > >
> > > https://lore.kernel.org/linux-arm-msm/1e7594dc-dca6-42e7-b478-b063e3325aff@xxxxxxxxxxxxxxxx/
> > >
> > > rpmh_read() will only retrieve the currently active values, so as-is,
> > > this hunk:
> > >
> > > +    /* For boot-up, fill the AMC vote in all buckets */
> > > +    for (i = 0; i < QCOM_ICC_NUM_BUCKETS; i++) {
> > > +        bcm->vote_x[i] = x;
> > > +        bcm->vote_y[i] = y;
> > > +    }
> > >
> > > is lying about the state of wake/sleep buckets
> > >
> > > this is ""fine"" today, as I don't see any "if (old_bw == new_bw)" checks
> > > across the framework, but debugfs is going to report incorrect values and
> > > if anyone decides to add the aforementioned check, it may introduce issues
> > > where the values aren't commited to the hardware (because Linux is going
> > > to believe they're already set)
> >
> > This is only for the pre-sync-state phase, where we don't need the wake/sleep
> > values but the interconnect rpmh implementation needs them, and anyway they will
> > be replaced by proper values in sync_state
>
> I realize this may not be the most convincing argument, but consider
> the case where sync_state can not be hit, for example with the Venus
> driver that requests FW at probe time and errors out if it's absent

We're talking about initial states here, if a device votes for an interconnect
path, even before sync_state, the path will be voted with the requested bandwidth.

https://elixir.bootlin.com/linux/v6.18.5/source/drivers/interconnect/core.c#L295

Before this patch:
node->init_avg & node->init_peak are set to INT_MAX, so max(x, INT_MAX) always gives INT_MAX
After this patch:
node->init_avg & node->init_peak are from the boot, which can be 0. So we either vote
for the requested bandwidth, or floor the bandwidth set by the bootloader (could be a higher value).

> > So this is an informed & assumed choice I did here. It's a small optimization
> > to avoid turning on _all_ interconnects at INT_MAX, and keep boot votes
> > up to sync_state.
>
> Another question is, whether that's a desired change - I could easily
> see pinning buses to the maximum speed helping boot time KPIs, but
> perhaps that could/should be configurable?

It's all about the rest of the bussed endpoints, enabling _all_ endpoints
to INT_MAX could potentially lead to in fact reducing bandwidth for crucial
devices like UFS because we configure everything to the max bandwidth, and enable
unused busses (and associated clocks & power domains) for nothing.

The idea in this patch is to keep the votes from bootloader, keep the disabled
endpoints and vote with requested bandwidth for devices which are used in the boot process.

Neil

> Konrad