[PATCH v5 0/4] Initial patch set for PURWA-IOT-EVK

[YijieYang]

From: Yijie Yang <yijie.yang@xxxxxxxxxxxxxxxx>

Introduce the device tree, DT bindings, and driver updates required to enable
the bring-up of the PURWA-IOT-EVK evaluation board. Focus is on two key
hardware components:

PURWA-IOT-SOM — A compact System-on-Module integrating the SoC, GPIOs, and
PMICs. Designed for modularity, it can pair with various carrier boards to
support diverse use cases.

PURWA-IOT-EVK — A carrier board tailored for IoT scenarios, providing
essential peripherals such as UART, on-board PMICs, and USB components.

Together, these components form a flexible and scalable platform. Initial
functionality is achieved through proper device tree configuration and driver
support.

The PURWA-IOT-EVK/SOM shares most of its hardware design with
HAMOA-IOT-EVK/SOM, differing primarily in the BOM. Consequently, the DTS files
are largely similar. Both platforms belong to Qualcomm’s IQ-X family. For more
details on the IQ-X series, see:
https://www.qualcomm.com/internet-of-things/products/iq-x-series

Hardware differences between HAMOA-IOT and PURWA-IOT:
- Display — PURWA uses a different number of clocks and frequency compared to
  HAMOA.
- GPU — PURWA integrates a different GPU.
- USB0 — PURWA uses a PS8833 retimer, while HAMOA employs an FSUSB42 as the
  SBU switch.

Features added and enabled:
- UART
- On-board regulators
- Regulators on the SOM
- PMIC GLINK
- USB0 through USB6 and their PHYs
- Embedded USB (eUSB) repeaters
- USB Type-C mux
- PCIe3, PCIe4, PCIe5, PCIe6a
- Reserved memory regions
- Pinctrl
- NVMe
- ADSP, CDSP
- WLAN, Bluetooth (M.2 interface)
- USB DisplayPort and eDP
- Graphics
- Audio
- TPM

Signed-off-by: Yijie Yang <yijie.yang@xxxxxxxxxxxxxxxx>
---
Changes in v2:
- Update the GPU firmware path.
- Update the description in the cover letter.
- Reorder the patches.
- Use separate DTS files for Purwa and Hamoa.
- Update base commit.
- Link to v1: https://lore.kernel.org/all/20251222-purwa-v1-0-14ab9316e5ff@xxxxxxxxxxxxxxxx/

Changes in v3:
- Delete unused PMIC and thermal nodes.
- Add WiFi node.
- Add display backlight node.
- Add connectors and VBUS regulators for USB3 and USB6.
- Enable PCIe3 and PCIe5; add PCIe ports along with reset and wake-up GPIOs.
- Link to v2: https://lore.kernel.org/r/20260109-purwa-v2-0-f39ee10684cb@xxxxxxxxxxxxxxxx

Changes in v4:
- Enable TPM.
- Update the descriptions for video and the USB OF graph.
- Link to v3: https://lore.kernel.org/all/20260113-purwa-v3-0-16eefacbdce9@xxxxxxxxxxxxxxxx/

Changes in v5:
- Reorder nodes in purwa-iot-evk.dts.
- Update base commit.
- The DT binding change that fixes the DT warning for pcie3_phy is located at: https://lore.kernel.org/linux-arm-msm/20260119-topic-purwa_phy_shutup_warning-v1-1-997a692b31c6@xxxxxxxxxxxxxxxx/T/#u
- Link to v4: https://lore.kernel.org/r/20260116-purwa-v4-0-89b2adae9f09@xxxxxxxxxxxxxxxx

---
Yijie Yang (4):
      dt-bindings: arm: qcom: Document PURWA-IOT-EVK board
      firmware: qcom: scm: Allow QSEECOM on PURWA-IOT-EVK
      arm64: dts: qcom: Add PURWA-IOT-SOM platform
      arm64: dts: qcom: Add base PURWA-IOT-EVK board

 Documentation/devicetree/bindings/arm/qcom.yaml |    6 +
 arch/arm64/boot/dts/qcom/Makefile               |    1 +
 arch/arm64/boot/dts/qcom/purwa-iot-evk.dts      | 1549 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/purwa-iot-som.dtsi     |  685 ++++++++++
 drivers/firmware/qcom/qcom_scm.c                |    1 +
 5 files changed, 2242 insertions(+)
---
base-commit: 6267b2da1b2d04847a1a8f441e138bc4a89435ee
change-id: 20251113-purwa-907ec75b4959

Best regards,
--  
Yijie Yang <yijie.yang@xxxxxxxxxxxxxxxx>