[PATCH 4/4] ARM: dts: imx6qdl-mba6: add boot phase properties
From: Max Merchel
Date: Wed Feb 18 2026 - 08:24:37 EST
Add boot phase properties to MBa6 device tree.
Signed-off-by: Max Merchel <Max.Merchel@xxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
index ee2c6bec92e8..74ccfe56828f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
@@ -206,6 +206,10 @@ ethphy: ethernet-phy@3 {
};
};
+&gpio1 {
+ bootph-pre-ram;
+};
+
&hdmi {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_hdmi>;
@@ -214,6 +218,8 @@ &hdmi {
};
&i2c1 {
+ bootph-pre-ram;
+
tlv320aic32x4: audio-codec@18 {
compatible = "ti,tlv320aic32x4";
reg = <0x18>;
@@ -274,6 +280,7 @@ &ssi1 {
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
+ bootph-pre-ram;
status = "okay";
};
@@ -346,6 +353,7 @@ &usdhc2 {
no-sdio;
cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ bootph-all;
status = "okay";
};
@@ -354,6 +362,7 @@ &wdog1 {
pinctrl-0 = <&pinctrl_wdog1>;
/* does not work on unmodified starter kit */
/* fsl,ext-reset-output; */
+ bootph-pre-ram;
status = "okay";
};
@@ -544,6 +553,7 @@ pinctrl_uart2: uart2grp {
MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b099
MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b099
>;
+ bootph-pre-ram;
};
pinctrl_uart3: uart3grp {
@@ -587,6 +597,7 @@ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017059
MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x0001b099 /* usdhc2 CD */
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x0001b099 /* usdhc2 WP */
>;
+ bootph-all;
};
pinctrl_usbotg: usbotggrp {
@@ -602,5 +613,6 @@ pinctrl_wdog1: wdog1grp {
/* Watchdog out */
MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x0000b099
>;
+ bootph-pre-ram;
};
};
--
2.43.0