[PATCH 2/3] arm64: dts: qcom: monaco-evk: Enable SDHCI for SD Card via overlay

[Monish Chunara]

The monaco EVK board supports either eMMC or SD-card, but only one
can be active at a time.

Enable the SD Host Controller Interface (SDHCI) on the monaco EVK board
to support SD Card for storage via a device tree overlay. This allows
eMMC support to be enabled through a separate overlay when required.

Signed-off-by: Monish Chunara <monish.chunara@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/Makefile             |  4 ++
 .../boot/dts/qcom/monaco-evk-sd-card.dtso     | 72 +++++++++++++++++++
 2 files changed, 76 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/monaco-evk-sd-card.dtso

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 317af937d038..c86242a1631d 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -46,6 +46,10 @@ lemans-evk-el2-dtbs := lemans-evk.dtb lemans-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-evk-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= milos-fairphone-fp6.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-evk.dtb
+
+monaco-evk-sd-card-dtbs := monaco-evk.dtb monaco-evk-sd-card.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += monaco-evk-sd-card.dtb
+
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8216-samsung-fortuna3g.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-acer-a1-724.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-alcatel-idol347.dtb
diff --git a/arch/arm64/boot/dts/qcom/monaco-evk-sd-card.dtso b/arch/arm64/boot/dts/qcom/monaco-evk-sd-card.dtso
new file mode 100644
index 000000000000..a0bc5c47d40b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/monaco-evk-sd-card.dtso
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+        vmmc_sdc: regulator-dummy {
+                compatible = "regulator-fixed";
+
+                regulator-name = "vmmc_sdc";
+                regulator-min-microvolt = <2950000>;
+                regulator-max-microvolt = <2950000>;
+        };
+
+        vreg_sdc: regulator-sdc {
+		compatible = "regulator-gpio";
+
+		regulator-name = "vreg_sdc";
+		regulator-type = "voltage";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpios = <&expander1 7 GPIO_ACTIVE_HIGH>;
+		states = <1800000 1>, <2950000 0>;
+
+		startup-delay-us = <100>;
+        };
+};
+
+&sdhc_1 {
+	vmmc-supply = <&vmmc_sdc>;
+	vqmmc-supply = <&vreg_sdc>;
+
+	pinctrl-0 = <&sdc1_state_on>, <&sd_cd>;
+	pinctrl-1 = <&sdc1_state_off>, <&sd_cd>;
+	pinctrl-names = "default", "sleep";
+
+	cap-sd-highspeed;
+	no-1-8-v;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
+	no-mmc;
+	no-sdio;
+
+	status = "okay";
+};
+
+&sdhc1_opp_table {
+	opp-100000000 {
+		opp-hz = /bits/ 64 <100000000>;
+		required-opps = <&rpmhpd_opp_low_svs>;
+	};
+
+	opp-202000000 {
+		opp-hz = /bits/ 64 <202000000>;
+		required-opps = <&rpmhpd_opp_svs_l1>;
+	};
+};
+
+&tlmm {
+        sd_cd: sd-cd-state {
+                pins = "gpio11";
+                function = "gpio";
+                bias-pull-up;
+        };
+};
-- 
2.34.1