[RFC v11 3/4] soc: microchip: add mpfs gpio interrupt mux driver

[Conor Dooley]

From: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>

On PolarFire SoC there are more GPIO interrupts than there are interrupt
lines available on the PLIC, and a runtime configurable mux is used to
decide which interrupts are assigned direct connections to the PLIC &
which are relegated to sharing a line.

Add a driver so that Linux can set the mux based on the interrupt
mapping in the devicetree.

Signed-off-by: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>
---
 MAINTAINERS                         |   2 +-
 drivers/soc/microchip/Kconfig       |  11 ++
 drivers/soc/microchip/Makefile      |   1 +
 drivers/soc/microchip/mpfs-irqmux.c | 167 ++++++++++++++++++++++++++++
 4 files changed, 180 insertions(+), 1 deletion(-)
 create mode 100644 drivers/soc/microchip/mpfs-irqmux.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 4044b28ca1818..55ed37ee53af0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22691,7 +22691,7 @@ F:	Documentation/devicetree/bindings/pinctrl/microchip,mpfs-pinctrl-mssio.yaml
 F:	Documentation/devicetree/bindings/pinctrl/microchip,pic64gx-pinctrl-gpio2.yaml
 F:	Documentation/devicetree/bindings/pwm/microchip,corepwm.yaml
 F:	Documentation/devicetree/bindings/riscv/microchip.yaml
-F:	Documentation/devicetree/bindings/soc/microchip/microchip,mpfs-sys-controller.yaml
+F:	Documentation/devicetree/bindings/soc/microchip/microchip,mpfs*.yaml
 F:	Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml
 F:	Documentation/devicetree/bindings/usb/microchip,mpfs-musb.yaml
 F:	arch/riscv/boot/dts/microchip/
diff --git a/drivers/soc/microchip/Kconfig b/drivers/soc/microchip/Kconfig
index bcf5546025610..7131f1b52d1bc 100644
--- a/drivers/soc/microchip/Kconfig
+++ b/drivers/soc/microchip/Kconfig
@@ -1,3 +1,14 @@
+config POLARFIRE_SOC_IRQ_MUX
+	bool "Microchip PolarFire SoC's GPIO IRQ Mux"
+	depends on ARCH_MICROCHIP
+	select REGMAP
+	select REGMAP_MMIO
+	default y
+	help
+	  Support for the interrupt mux on Polarfire SoC. It sits between
+	  the GPIO controllers and the PLIC, as only 35 interrupts are shared
+	  between 3 GPIO controllers with 32 interrupts each.
+
 config POLARFIRE_SOC_SYS_CTRL
 	tristate "Microchip PolarFire SoC (MPFS) system controller support"
 	depends on POLARFIRE_SOC_MAILBOX
diff --git a/drivers/soc/microchip/Makefile b/drivers/soc/microchip/Makefile
index 1a3a1594b089b..55775db45ee76 100644
--- a/drivers/soc/microchip/Makefile
+++ b/drivers/soc/microchip/Makefile
@@ -1,2 +1,3 @@
+obj-$(CONFIG_POLARFIRE_SOC_IRQ_MUX)	+= mpfs-irqmux.o
 obj-$(CONFIG_POLARFIRE_SOC_SYS_CTRL)	+= mpfs-sys-controller.o
 obj-$(CONFIG_POLARFIRE_SOC_SYSCONS)	+= mpfs-control-scb.o mpfs-mss-top-sysreg.o
diff --git a/drivers/soc/microchip/mpfs-irqmux.c b/drivers/soc/microchip/mpfs-irqmux.c
new file mode 100644
index 0000000000000..76c1afa1fe1c4
--- /dev/null
+++ b/drivers/soc/microchip/mpfs-irqmux.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Largely copied from rzn1_irqmux.c
+ */
+
+#include <linux/bitmap.h>
+#include <linux/bitops.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define MPFS_IRQMUX_CR		0x54
+#define MPFS_IRQMUX_NUM_OUTPUTS	70
+
+static int mpfs_irqmux_is_direct_mode(struct device *dev,
+				      const struct of_phandle_args *parent_args)
+{
+	if (parent_args->args_count != 1) {
+		dev_err(dev, "Invalid interrupt-map item\n");
+		return -EINVAL;
+	}
+
+	if (parent_args->args[0] < 13 || parent_args->args[0] > 53) {
+		dev_err(dev, "Invalid interrupt %u\n", parent_args->args[0]);
+		return -EINVAL;
+	}
+
+	if (parent_args->args[0] > 50)
+		return 0;
+
+	return 1;
+}
+
+static int mpfs_irqmux_probe(struct platform_device *pdev)
+{
+	DECLARE_BITMAP(line_done, MPFS_IRQMUX_NUM_OUTPUTS) = {};
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct of_imap_parser imap_parser;
+	struct of_imap_item imap_item;
+	struct regmap *regmap;
+	int ret, direct_mode, line, controller, gpio;
+	u32 tmp, val = 0, old;
+
+	regmap = device_node_to_regmap(pdev->dev.parent->of_node);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap), "Failed to find syscon regmap\n");
+
+	/* We support only #interrupt-cells = <1> and #address-cells = <0> */
+	ret = of_property_read_u32(np, "#interrupt-cells", &tmp);
+	if (ret)
+		return ret;
+	if (tmp != 1)
+		return -EINVAL;
+
+	ret = of_property_read_u32(np, "#address-cells", &tmp);
+	if (ret)
+		return ret;
+	if (tmp != 0)
+		return -EINVAL;
+
+	ret = of_imap_parser_init(&imap_parser, np, &imap_item);
+	if (ret)
+		return ret;
+
+	for_each_of_imap_item(&imap_parser, &imap_item) {
+
+		direct_mode = mpfs_irqmux_is_direct_mode(dev, &imap_item.parent_args);
+		if (direct_mode < 0) {
+			of_node_put(imap_item.parent_args.np);
+			return direct_mode;
+		}
+
+		line = imap_item.child_imap[0];
+		gpio = line % 32;
+		controller = line / 32;
+
+		if (controller > 2) {
+			of_node_put(imap_item.parent_args.np);
+			dev_err(dev, "child interrupt number too large: %d\n", line);
+			return -EINVAL;
+		}
+
+		if (test_and_set_bit(line, line_done)) {
+			of_node_put(imap_item.parent_args.np);
+			dev_err(dev, "Mux output line %d already defined in interrupt-map\n",
+				line);
+			return -EINVAL;
+		}
+
+		/*
+		 * There are 41 interrupts assigned to GPIOs, of which 38 are "direct". Since the
+		 * mux has 32 bits only, 6 of these exclusive/"direct" interrupts remain. These
+		 * are used by GPIO controller 1's lines 18 to 23. Nothing needs to be done
+		 * for these interrupts.
+		 */
+		if (controller == 1 && gpio >= 18)
+			continue;
+
+		/*
+		 * The mux has a single register, where bits 0 to 13 mux between GPIO controller
+		 * 1's 14 GPIOs and GPIO controller 2's first 14 GPIOs. The remaining bits mux
+		 * between the first 18 GPIOs of controller 1 and the last 18 GPIOS of
+		 * controller 2. If a bit in the mux's control register is set, the
+		 * corresponding interrupt line for GPIO controller 0 or 1 will be put in
+		 * "non-direct" mode. If cleared, the "fabric" controller's will.
+		 *
+		 * Register layout:
+		 *    GPIO 1 interrupt line 17 | mux bit 31 | GPIO 2 interrupt line 31
+		 *    ...                      | ...        | ...
+		 *    ...                      | ...        | ...
+		 *    GPIO 1 interrupt line  0 | mux bit 14 | GPIO 2 interrupt line 14
+		 *    GPIO 0 interrupt line 13 | mux bit 13 | GPIO 2 interrupt line 13
+		 *    ...                      | ...        | ...
+		 *    ...                      | ...        | ...
+		 *    GPIO 0 interrupt line  0 | mux bit  0 | GPIO 2 interrupt line  0
+		 *
+		 * As the binding mandates 70 items, one for each GPIO line, there's no need to
+		 * handle anything for GPIO controller 2, since the bit will be set for the
+		 * corresponding line in GPIO controller 0 or 1.
+		 */
+		if (controller == 2)
+			continue;
+
+		/*
+		 * If in direct mode, the bit is cleared, nothing needs to be done as val is zero
+		 * initialised and that's the direct mode setting for GPIO controller 0 and 1.
+		 */
+		if (direct_mode)
+			continue;
+
+		if (controller == 0)
+			val |= 1U << gpio;
+		else
+			val |= 1U << (gpio + 14);
+	}
+
+	regmap_read(regmap, MPFS_IRQMUX_CR, &old);
+	regmap_write(regmap, MPFS_IRQMUX_CR, val);
+
+	if (val != old)
+		dev_info(dev, "firmware mux setting of 0x%x overwritten to 0x%x\n", old, val);
+
+	return 0;
+}
+
+static const struct of_device_id mpfs_irqmux_of_match[] = {
+	{ .compatible = "microchip,mpfs-irqmux", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, mpfs_irqmux_of_match);
+
+static struct platform_driver mpfs_irqmux_driver = {
+	.probe = mpfs_irqmux_probe,
+	.driver = {
+		.name = "mpfs_irqmux",
+		.of_match_table = mpfs_irqmux_of_match,
+	},
+};
+module_platform_driver(mpfs_irqmux_driver);
+
+MODULE_AUTHOR("Conor Dooley <conor.dooley@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Polarfire SoC interrupt mux driver");
+MODULE_LICENSE("GPL");
-- 
2.51.0