Re: [PATCH 1/4] arm64: dts: imx952: Add audio device nodes
From: Daniel Baluta
Date: Thu Mar 12 2026 - 02:40:25 EST
On 3/12/26 05:49, Shengjiu Wang wrote:
> Add audio device nodes, include SAI, MICFIL, ASRC, Audio Mixer.
>
> Signed-off-by: Shengjiu Wang <shengjiu.wang@xxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/imx952.dtsi | 199 ++++++++++++++++++++++
> 1 file changed, 199 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx952.dtsi b/arch/arm64/boot/dts/freescale/imx952.dtsi
> index 0f86b5626cdd..5787c12e788f 100644
> --- a/arch/arm64/boot/dts/freescale/imx952.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx952.dtsi
> @@ -823,6 +823,156 @@ usdhc3: mmc@42c40000 {
> };
> };
>
> + aips5: bus@43000000 {
> + compatible = "fsl,aips-bus", "simple-bus";
> + reg = <0 0x43000000 0 0x800000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x43000000 0x0 0x43000000 0x800000>;
> +
> + asrc1: asrc@43000000 {
> + compatible = "fsl,imx952-asrc";
> + reg = <0x43000000 0x10000>;
> + interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX952_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX952_CLK_BUSWAKEUP>,
> + <&scmi_clk IMX952_CLK_ASRC1>,
> + <&scmi_clk IMX952_CLK_ASRC2>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>,
> + <&clk_dummy>;
> + clock-names = "mem", "ipg",
> + "asrck_0", "asrck_1", "asrck_2", "asrck_3",
> + "asrck_4", "asrck_5", "asrck_6", "asrck_7",
> + "asrck_8", "asrck_9", "asrck_a", "asrck_b",
> + "asrck_c", "asrck_d", "asrck_e", "asrck_f",
> + "spba";
> + dmas = <&edma2 97 0 0>, <&edma2 98 0 0>, <&edma2 99 0 0>,
> + <&edma2 100 0 1>, <&edma2 101 0 1>, <&edma2 102 0 1>;
For consistency we should use symbolic macros for directions like you did below.
Use FSL_EDMA_RX for rx direction and also introduce FSL_EDMA_TX for tx direction.
> + dma-names = "rxa", "rxb", "rxc",
> + "txa", "txb", "txc";
> + #sound-dai-cells = <0>;
> + fsl,asrc-rate = <8000>;
> + fsl,asrc-width = <16>;
> + status = "disabled";
> + };
[...]
> + sai3: sai@433e0000 {
> + compatible = "fsl,imx952-sai", "fsl,imx95-sai";
> + reg = <0x433e0000 0x10000>;
> + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&scmi_clk IMX952_CLK_BUSWAKEUP>, <&clk_dummy>,
> + <&scmi_clk IMX952_CLK_SAI3>, <&clk_dummy>,
> + <&clk_dummy>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
> + dmas = <&edma2 61 0 FSL_EDMA_RX>, <&edma2 60 0 0>;
As I said we should introduce FSL_EDMA_TX and this will read as:
dmas = <&edma2 61 0 FSL_EDMA_RX>, <&edma2 60 0 FSL_EDMA_TX>;
Otherwise, looks good to me.