[PATCH v2 10/10] arm64: dts: renesas: r9a08g046l48-smarc: Add USB2.0 support

[Biju]

From: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>

Enable USB2.0 on the RZ/G3L SMARC board (r9a08g046l48-smarc).

Port 0 (ehci0, ohci0, usb2_phy0) is configured as OTG with
usb0_pins pinmux (USB20_OVRCUR, USB20_VBUSEN) and usb0_vbus_otg
as the VBUS supply. Port 1 (ehci1, ohci1, usb2_phy1) is configured
as host-only with usb1_pins pinmux (USB21_OVRCUR, USB21_VBUSEN),
usb1_vbus_otg as the VBUS supply, and renesas,no-otg-pins set to
indicate no OTG pin routing. The phyrst USB PHY reset controller is
also enabled.

Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
---
v1->v2:
 * Updated commit description.
---
 .../boot/dts/renesas/r9a08g046l48-smarc.dts   | 49 +++++++++++++++++++
 1 file changed, 49 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
index 96cc7ee46a6a..b189ae8e808d 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
@@ -87,6 +87,16 @@ vqmmc_sd1_pvdd: regulator-vqmmc-sd1-pvdd {
 #endif
 };
 
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ehci1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
 &i2c2 {
 	pinctrl-0 = <&i2c2_pins>;
 	pinctrl-names = "default";
@@ -138,6 +148,20 @@ &keys {
 #endif
 };
 
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&phyrst {
+	status = "okay";
+};
+
 &pinctrl {
 	audio_clk_pins: audio-clock {
 		pinmux = <RZG3L_PORT_PINMUX(H, 4, 6)>, /* AUDIO_CLK_B */
@@ -259,6 +283,16 @@ ssi0_pins: ssi0 {
 			 <RZG3L_PORT_PINMUX(H, 2, 9)>, /* SSIF0_RCK */
 			 <RZG3L_PORT_PINMUX(H, 3, 9)>; /* SSIF0_TXD */
 	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG3L_PORT_PINMUX(3, 0, 12)>, /* USB20_OVRCUR */
+			 <RZG3L_PORT_PINMUX(3, 1, 12)>; /* USB20_VBUSEN */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG3L_PORT_PINMUX(3, 4, 12)>, /* USB21_OVRCUR */
+			 <RZG3L_PORT_PINMUX(3, 5, 12)>; /* USB21_VBUSEN */
+	};
 };
 
 #if SW_SER0_PMOD
@@ -330,3 +364,18 @@ &ssi0 {
 	status = "okay";
 };
 #endif
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+	vbus-supply = <&usb1_vbus_otg>;
+	renesas,no-otg-pins;
+	status = "okay";
+};
-- 
2.43.0