[PATCH v2 0/2] Add driver for DAC8163:

[Lukas Metz]

This series adds an IIO driver for the Texas Instruments DAC7562, DAC7563,
DAC8162, DAC8163, DAC8562, and DAC8563 dual-channel voltage-output DACs.

These devices are pin-compatible 12-, 14-, and 16-bit variants sharing the
same 24-bit SPI command interface. Each device provides two independently
addressable output channels and includes a 2.5 V, 4 ppm/°C internal
reference that can be enabled via device tree, or an external reference
supplied through a regulator. The register and command structure differs
from already existing drivers which makes adding a new driver a
reasonable choice in my opinion.

The driver supports:
 - All six device variants via a shared chip info table
 - DAC updates in synchronous mode
 - Configurable internal or external voltage reference
 - Optional LDAC GPIO which has to be asserted permanently when using
   synchronous updates.
 - IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE attributes per channel

Datasheet (DAC8163):
  https://www.ti.com/lit/gpn/dac8163

The driver was tested with a DAC8163 on a custom STM32MP157F board with
external reference enabled.

Signed-off-by: Lukas Metz <lukas.metz@xxxxxxx>
---
Changes in v2:
- add reg_defaults to initialize the output registers based on
  the device (dacxxx2 resets to 0, dacxxx3 resets to mid-scale)
- add variable gain to dac8163_state struct to report correct scale when
  internal reference is used (the device sets the gain register to 2
  when the internal reference is selected)
- do a full reset of the device when probing to ensure we have a known
  device state as pointed out by Jonathan Cameron
- use devm* calls where possible and omit remove callback
- make use of regmap and remove now unneeded things like manual locking
  and caching of output register values (thanks to Andy Shevchenko,
  David Lechner and others for the hint)
- remove internal_reference property
- add missing headers as suggested by Siratul Islam
- remove debug print from dac8163_write_raw (per Andy Shevchenko and
  David Lechner)
- switch ldac-gpio polarity for consistency with datasheet (as per David
  Lechner)
- rename dt properties ti,loaddacs-gpios to ldac-gpios and vref-supply to
  vrefin-supply
- add required spi property spi-cpha to binding (the device only works
  in spi mode 1 and 3)
- add missing spi properties spi-max-frequency and spi-rx-bus-width to
  binding
- add avdd-supply to binding and enable it in the driver (thanks to
  David Lechner)
- add clr-gpios to binding although not yet supported by the driver
- add nullptr check after calling spi_get_device_match_data (thanks to
  Andy Shevchenko for pointing this out)
- add comment for permanent ldac assertion
- switch to GPL-2.0-or-later
- return -ERANGE when raw write is out of range
- use named structures instead of chip_info array
- rename driver identifiers from dacxx6x to dac8163 and partly remove
  vendor prefix as suggested by David Lechner and Siratul Islam
- remove redundant call to gpiod_set_value
- Link to v1: https://patch.msgid.link/20260623-dac8163-work-v1-0-5b508158faa0@xxxxxxx

---
Lukas Metz (2):
      dt-bindings: iio: dac: Add DAC8163
      iio: dac: dac8163: Add driver for DAC8163

 .../devicetree/bindings/iio/dac/ti,dac8163.yaml    |  85 +++++
 MAINTAINERS                                        |   7 +
 drivers/iio/dac/Kconfig                            |  15 +
 drivers/iio/dac/Makefile                           |   1 +
 drivers/iio/dac/ti-dac8163.c                       | 373 +++++++++++++++++++++
 5 files changed, 481 insertions(+)
---
base-commit: 76b6720279964612111352ca5d09f5bd61e41ce4
change-id: 20260413-dac8163-work-2138a775b515

Best regards,
--  
Lukas <lukas.metz@xxxxxxx>