Re: [PATCH net-next 1/4] dpll: zl3073x: add channel ToD and phase step operations

[Vadim Fedorenko]

On 08/07/2026 18:05, Ivan Vecera wrote:
> Add low-level DPLL channel operations for ToD read/write/adjust,
> delta frequency offset write and output phase step. ToD operations
> use a wait-before-write pattern to avoid blocking after each
> operation. tod_adjust additionally waits for completion since callers
> may follow with phase step operations.
>
> The tod_ready_wait helper selects the poll timeout based on the
> current ToD command - write operations use a longer timeout (1000 ms)
> than reads (30 ms).
>
> The ToD read captures system timestamps (ptp_system_timestamp) around
> the HW command and completion poll to support cross-timestamping.
>
> Add output step-time mask invariant to zl3073x_chan and
> zl3073x_chan_is_out_stepped() helper to check if an output
> participates in step-time operations.

[...]

> +/**
> + * zl3073x_chan_tod_read - read ToD registers after issuing a command
> + * @zldev: pointer to zl3073x device
> + * @ch: DPLL channel index
> + * @next_hz: if true, read predicted ToD at next 1 Hz; otherwise read current
> + * @ts: timespec to store the result
> + * @sts: optional system timestamp pair for cross-timestamping
> + *
> + * Context: Caller must serialize all zl3073x_chan_tod_* calls externally.
> + * Return: 0 on success, <0 on error
> + */
> +int zl3073x_chan_tod_read(struct zl3073x_dev *zldev, u8 ch,
> +			  bool next_hz, struct timespec64 *ts,
> +			  struct ptp_system_timestamp *sts)
> +{
> +	u32 nsec;
> +	u64 sec;
> +	u8 cmd;
> +	int rc;
> +
> +	if (next_hz)
> +		cmd = ZL_DPLL_TOD_CTRL_CMD_RD_NEXT_1HZ;
> +	else
> +		cmd = ZL_DPLL_TOD_CTRL_CMD_RD_CURRENT;
> +
> +	/* Wait for any previous ToD operation to complete */
> +	rc = zl3073x_chan_tod_ready_wait(zldev, ch);
> +	if (rc)
> +		return rc;
> +
> +	ptp_read_system_prets(sts);
> +	rc = zl3073x_chan_tod_ctrl(zldev, ch, cmd);
> +	if (rc)
> +		return rc;
> +
> +	rc = zl3073x_chan_tod_ready_wait(zldev, ch);
> +	if (rc)
> +		return rc;
> +	ptp_read_system_postts(sts);

AFAIU, this code means that the ToD value was somewhere between tod_ctrl
command and tod_ready read value 0 of the register. How does it work
with "predicted ToD at next 1 Hz"?

> +
> +	rc = zl3073x_read_u48(zldev, ZL_REG_DPLL_TOD_SEC(ch), &sec);
> +	if (rc)
> +		return rc;
> +
> +	/* HW nanoseconds are always in [0, NSEC_PER_SEC) range */
> +	rc = zl3073x_read_u32(zldev, ZL_REG_DPLL_TOD_NS(ch), &nsec);
> +	if (rc)
> +		return rc;
> +
> +	ts->tv_sec = sec;
> +	ts->tv_nsec = nsec;
> +
> +	return 0;
> +}
[...]