Re: [PATCH v3 00/11] arm64: dts: qcom: Add x1e/Hamoa camera DTSI

[Bjorn Andersson]

On Wed, Jul 15, 2026 at 03:52:47PM -0500, Bjorn Andersson wrote:
> On Wed, Jul 08, 2026 at 10:33:12PM +0100, Bryan O'Donoghue wrote:
> > On 08/07/2026 22:11, Bryan O'Donoghue wrote:
> > > On 08/07/2026 15:56, Bjorn Andersson wrote:
> > > > Applied, thanks!
> > > > 
> > > > [01/11] arm64: dts: qcom: x1e80100: Add CAMCC block definition
> > > >          commit: 6a3568f938c9ff2cb493f82dc595b4dc2760f517
> > > > [02/11] arm64: dts: qcom: x1e80100: Add CCI definitions
> > > >          (no commit info)
> > > > [03/11] arm64: dts: qcom: x1e80100: Add CAMSS block definition
> > > >          (no commit info)
> > > > [04/11] arm64: dts: qcom: x1e80100-crd: Add pm8010 CRD pmic,id=m
> > > > regulators
> > > >          (no commit info)
> > > > [05/11] arm64: dts: qcom: x1e80100-crd: Add ov08x40 RGB sensor on CSIPHY4
> > > >          (no commit info)
> > > > [06/11] arm64: dts: qcom: x1e80100-t14s: Add pm8010 camera PMIC with
> > > > voltage levels for IR and RGB camera
> > > >          (no commit info)
> > > > [07/11] arm64: dts: qcom: x1e80100-t14s: Add on ov02c10 RGB sensor
> > > > on CSIPHY4
> > > >          (no commit info)
> > > > [08/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add pm8010
> > > > camera PMIC with voltage levels for IR and RGB camera
> > > >          (no commit info)
> > > > [09/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add l7b_2p8
> > > > voltage regulator for RGB camera
> > > >          (no commit info)
> > > > [10/11] arm64: dts: qcom: x1e80100-lenovo-yoga-slim7x: Add ov02c10
> > > > RGB sensor on CSIPHY4
> > > >          (no commit info)
> > > > [11/11] arm64: dts: qcom: x1e80100-dell-inspiron14-7441: Switch on
> > > > CAMSS RGB sensor
> > > >          (no commit info)
> > > > 
> > > > Best regards,
> > > > -- Bjorn Andersson <andersson@xxxxxxxxxx>
> > > 
> > > Bjorn.
> > > 

Sorry, should have paid a bit more attention here.

I believe I had previously tried to apply part of this series, just to
realize that the bindings weren't in place - and hence backed them out
again.

So the change I actually merged was [1], but for some reason we got a
ty-letter on this series.

[1] https://lore.kernel.org/all/20260507-purwa-videocc-camcc-v5-6-fc3af4130282@xxxxxxxxxxxxxxxx/ 

> > > This is v3 from March. We are on v12. I don't think you meant to apply
> > > this.

I have v3, v4, and v5 of the camcc addition, I merged v5. I'm not able
to figure what series you're talking about, but it must be something
else?

> > > 
> > > ---
> > > bod
> > 
> > For example: compatible = "qcom,x1e80100-csi2-phy"; is not a valid binding

It doesn't say anywhere that I merged the csi2-phy nodes, above
ty-letter states that I merged the camcc patch.

> > 
> > Please revert.
> > 
> 
> Done
> 

And the revert is dropped as it was incorrect, sorry about that.

Regards,
Bjorn

> Regards,
> Bjorn
> 
> 
> > ---
> > bod
> > 
>