[PATCH 3/3] serial: qcom-geni: Use geni_se_set_perf_level() for baud rate perf level

[Praveen Talari]

The driver implements its own helper to select the performance level
corresponding to a requested baud rate. The helper duplicates
functionality already provided by geni_se_set_perf_level() in the GENI
core.

Replace the local implementation with the common helper and remove the
associated duplicate definitions and code. This consolidates
performance-level management in the GENI framework and reduces driver
specific code.

Signed-off-by: Praveen Talari <praveen.talari@xxxxxxxxxxxxxxxx>
---
 drivers/tty/serial/qcom_geni_serial.c | 53 ++++++-----------------------------
 1 file changed, 8 insertions(+), 45 deletions(-)

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 17735c940541..fa86dd18fdee 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -107,14 +107,12 @@
 #define DMA_RX_BUF_SIZE		2048
 
 static DEFINE_IDA(port_ida);
-#define DOMAIN_IDX_POWER	0
-#define DOMAIN_IDX_PERF		1
 
 struct qcom_geni_device_data {
 	bool console;
 	enum geni_se_xfer_mode mode;
 	int (*resources_init)(struct geni_se *se);
-	int (*set_rate)(struct uart_port *uport, unsigned int baud);
+	int (*set_rate)(struct geni_se *se, unsigned long baud);
 	int (*power_on)(struct geni_se *se);
 	int (*power_off)(struct geni_se *se);
 };
@@ -1284,9 +1282,10 @@ static int qcom_geni_serial_startup(struct uart_port *uport)
 	return 0;
 }
 
-static int geni_serial_set_rate(struct uart_port *uport, unsigned int baud)
+static int geni_serial_set_rate(struct geni_se *se, unsigned long baud)
 {
-	struct qcom_geni_serial_port *port = to_dev_port(uport);
+	struct qcom_geni_serial_port *port = dev_get_drvdata(se->dev);
+	struct uart_port *uport = &port->uport;
 	unsigned long clk_rate;
 	unsigned int avg_bw_core, clk_idx;
 	unsigned int clk_div;
@@ -1302,7 +1301,7 @@ static int geni_serial_set_rate(struct uart_port *uport, unsigned int baud)
 
 	ret = geni_se_clk_freq_match(&port->se, baud * sampling_rate, &clk_idx, &clk_rate, false);
 	if (ret) {
-		dev_err(port->se.dev, "Failed to find src clk for baud rate: %d ret: %d\n",
+		dev_err(port->se.dev, "Failed to find src clk for baud rate: %lu ret: %d\n",
 			baud, ret);
 		return ret;
 	}
@@ -1340,42 +1339,6 @@ static int geni_serial_set_rate(struct uart_port *uport, unsigned int baud)
 	return 0;
 }
 
-static int geni_serial_set_level(struct uart_port *uport, unsigned int baud)
-{
-	struct qcom_geni_serial_port *port = to_dev_port(uport);
-	struct device *perf_dev = port->se.pd_list->pd_devs[DOMAIN_IDX_PERF];
-
-	/*
-	 * The performance protocol sets UART communication
-	 * speeds by selecting different performance levels
-	 * through the OPP framework.
-	 *
-	 * Supported perf levels for baudrates in firmware are below
-	 * +---------------------+--------------------+
-	 * |  Perf level value   |  Baudrate values   |
-	 * +---------------------+--------------------+
-	 * |      300            |      300           |
-	 * |      1200           |      1200          |
-	 * |      2400           |      2400          |
-	 * |      4800           |      4800          |
-	 * |      9600           |      9600          |
-	 * |      19200          |      19200         |
-	 * |      38400          |      38400         |
-	 * |      57600          |      57600         |
-	 * |      115200         |      115200        |
-	 * |      230400         |      230400        |
-	 * |      460800         |      460800        |
-	 * |      921600         |      921600        |
-	 * |      2000000        |      2000000       |
-	 * |      3000000        |      3000000       |
-	 * |      3200000        |      3200000       |
-	 * |      4000000        |      4000000       |
-	 * +---------------------+--------------------+
-	 */
-
-	return dev_pm_opp_set_level(perf_dev, baud);
-}
-
 static void qcom_geni_serial_set_termios(struct uart_port *uport,
 					 struct ktermios *termios,
 					 const struct ktermios *old)
@@ -1394,7 +1357,7 @@ static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	/* baud rate */
 	baud = uart_get_baud_rate(uport, termios, old, 300, 8000000);
 
-	ret = port->dev_data->set_rate(uport, baud);
+	ret = port->dev_data->set_rate(&port->se, baud);
 	if (ret)
 		return;
 
@@ -2010,7 +1973,7 @@ static const struct qcom_geni_device_data sa8255p_qcom_geni_console_data = {
 	.console = true,
 	.mode = GENI_SE_FIFO,
 	.resources_init = geni_se_domain_attach,
-	.set_rate = geni_serial_set_level,
+	.set_rate = geni_se_set_perf_level,
 };
 #endif
 
@@ -2027,7 +1990,7 @@ static const struct qcom_geni_device_data sa8255p_qcom_geni_uart_data = {
 	.console = false,
 	.mode = GENI_SE_DMA,
 	.resources_init = geni_se_domain_attach,
-	.set_rate = geni_serial_set_level,
+	.set_rate = geni_se_set_perf_level,
 };
 
 static const struct dev_pm_ops qcom_geni_serial_pm_ops = {

-- 
2.34.1