[PATCH] arm64: dts: qcom: hamoa-iot-evk: switch typec0 to PS8830 retimer

[Xin Liu]

The Hamoa IoT EVK populates a Parade PS8830 retimer on I2C3 for the
TypeC 0 port to support USB3.0 and SBU muxing. Describe the PS8830 and
route typec0 through it.

The vreg_rtmr0_* rails provisioned for a retimer were already defined
but previously wired to nowhere. They are now consumed by the PS8830,
so drop the "Left unused" comment.

The FSUSB42 SBU mux chip won't be populated on the final EVK
board, so remove the fsusb42 node and its pinctrl group.

Signed-off-by: Guodong Xu <guodong.xu@xxxxxxxxxxxxxxxx>
Signed-off-by: Xin Liu <xin.liu@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 108 ++++++++++++---------
 1 file changed, 60 insertions(+), 48 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 9fa86bb6438e..a3ca22f9c3e8 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -126,15 +126,15 @@ port@1 {
 					reg = <1>;
 
 					pmic_glink_ss0_ss_in: endpoint {
-						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+						remote-endpoint = <&retimer_ss0_ss_out>;
 					};
 				};
 
 				port@2 {
 					reg = <2>;
 
-					pmic_glink_ss0_sbu: endpoint {
-						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
 					};
 				};
 			};
@@ -303,7 +303,6 @@ vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
 		pinctrl-names = "default";
 	};
 
-	/* Left unused as the retimer is not used on this board. */
 	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
 		compatible = "regulator-fixed";
 
@@ -658,25 +657,6 @@ platform {
 		};
 	};
 
-	usb-1-ss0-sbu-mux {
-		compatible = "onnn,fsusb42", "gpio-sbu-mux";
-
-		enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
-		select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
-
-		pinctrl-0 = <&usb_1_ss0_sbu_default>;
-		pinctrl-names = "default";
-
-		mode-switch;
-		orientation-switch;
-
-		port {
-			usb_1_ss0_sbu_mux: endpoint {
-				remote-endpoint = <&pmic_glink_ss0_sbu>;
-			};
-		};
-	};
-
 	wcn7850-pmu {
 		compatible = "qcom,wcn7850-pmu";
 
@@ -793,6 +773,62 @@ retimer_ss2_con_sbu_out: endpoint {
 	};
 };
 
+&i2c3 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK4>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		orientation-switch;
+		retimer-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
 &i2c5 {
 	clock-frequency = <400000>;
 
@@ -1458,30 +1494,6 @@ usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state {
 		bias-disable;
 	};
 
-	usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
-		mode-pins {
-			pins = "gpio166";
-			function = "gpio";
-			bias-disable;
-			drive-strength = <2>;
-			output-high;
-		};
-
-		oe-n-pins {
-			pins = "gpio168";
-			function = "gpio";
-			bias-disable;
-			drive-strength = <2>;
-		};
-
-		sel-pins {
-			pins = "gpio167";
-			function = "gpio";
-			bias-disable;
-			drive-strength = <2>;
-		};
-	};
-
 	wcd_default: wcd-reset-n-active-state {
 		pins = "gpio191";
 		function = "gpio";
@@ -1578,7 +1590,7 @@ &usb_1_ss0_hsphy {
 };
 
 &usb_1_ss0_qmpphy_out {
-	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+	remote-endpoint = <&retimer_ss0_ss_in>;
 };
 
 &usb_1_ss1_dwc3_hs {
-- 
2.43.0