Re: [PATCH v1 0/7] Add HPD support for Rockchip Analogix DP
From: Damon Ding
Date: Thu Jul 30 2026 - 23:19:22 EST
Hi Heiko,
On 7/31/2026 2:49 AM, Heiko Stübner wrote:
Hi Damon,
Am Donnerstag, 30. Juli 2026, 05:27:37 Mitteleuropäische Sommerzeit schrieb Damon Ding:
This series improves the HPD (Hotplug Detect) interrupt handling in
the Analogix DP driver to enable reliable native HPD pin detection on
Rockchip platforms, and introduces platform-specific HPD detection
schemes with fine-grained interrupt control.
[...]
Tested on RK3576 with both native HPD pin and GPIO HPD configurations.
Native HPD pin mode:
&edp {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&edp_txm0_pins>;
};
GPIO HPD mode:
&edp {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&edp0_hpd>;
hpd-gpios = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>;
};
&pinctrl {
edp {
edp0_hpd: edp0-hpd {
rockchip,pins = <4 RK_PC1 0 &pcfg_pull_none>;
};
};
};
Yay and thanks a lot for working on that.
If I roll my display-port carrier board back to the analogix-dp being
the endpoint, this works exactly as expected :-) .
I can plug in the display at some point after the boot and have it
detected and setup correctly. Same with unplugging it while
the system is running. The connection status is correctly reported
in sysfs.
Though there is a caveat. When the eDP is not the last part, this does not
work anymore. The detect function always returns "connected" if there is
a next bridge available.
My board [0] has a physical DP connector on it, so models it as
dp-connector, but in that case the Analogix driver always reports being
connected.
[0] https://lore.kernel.org/linux-rockchip/20251009225050.88192-3-heiko@xxxxxxxxx/
... same effect with hpd-gpios in either the edp node or dp-connector node
My previous tests were carried out on the modified RK3576 IOTEST board DTS based on RK3576 EVB1, which includes dp-connector by default. I also did extra verification without dp-connector, and HPD detection works correctly in both cases.
I've taken a look at the Tiger board DT configuration. The pinctrl settings for the eDP HPD GPIO may need adjustment:
&pinctrl {
edp0 {
edp0_hpd_l: edp0-hpd-l-pin {
rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
};
It is recommended to configure GPIO4B5 as pull-down or pll-none. Pull-up configuration may prevent GPIO interrupts from being triggered properly, resulting in a permanent "connected" status.
Could you help try this modification and see if it resolves the issue?
Best regards,
Damon
From 1fb4d0c29681407367c8d93770c30c2213174473 Mon Sep 17 00:00:00 2001
From: Damon Ding <damon.ding@xxxxxxxxxxxxxx>
Date: Tue, 28 Jul 2026 10:00:18 +0800
Subject: [PATCH] [TEST]arm64: dts: rockchip: Enable eDP2DP display on RK3576
IOTEST board
Signed-off-by: Damon Ding <damon.ding@xxxxxxxxxxxxxx>
---
.../boot/dts/rockchip/rk3576-iotest-v10.dts | 1126 +++++++++++++++++
1 file changed, 1126 insertions(+)
create mode 100755 arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts b/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts
new file mode 100755
index 000000000000..197087c831f6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-iotest-v10.dts
@@ -0,0 +1,1126 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3576.dtsi"
+
+/ {
+ model = "Rockchip RK3576 EVB V10 Board";
+ compatible = "rockchip,rk3576-evb1-v10", "rockchip,rk3576";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <&vcc3v3_lcd_n>;
+ pwms = <&gpio_pwm0 0 25000 0>;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial0:1500000n8";
+ bootargs = "root=PARTUUID=614e0000-0000 rootwait";
+ };
+
+ adc_keys: adc-keys {
+ compatible = "adc-keys";
+ io-channels = <&saradc 1>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <100>;
+
+ button-back {
+ label = "back";
+ linux,code = <KEY_BACK>;
+ press-threshold-microvolt = <1235000>;
+ };
+
+ button-menu {
+ label = "menu";
+ linux,code = <KEY_MENU>;
+ press-threshold-microvolt = <890000>;
+ };
+
+ button-vol-down {
+ label = "volume down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ press-threshold-microvolt = <417000>;
+ };
+
+ button-vol-up {
+ label = "volume up";
+ linux,code = <KEY_VOLUMEUP>;
+ press-threshold-microvolt = <17000>;
+ };
+ };
+
+ dp-con {
+ compatible = "dp-connector";
+ label = "DP OUT";
+ type = "full-size";
+
+ port {
+ dp_con_in: endpoint {
+ remote-endpoint = <&edp_out_conn>;
+ };
+ };
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+
+ work_led: led-0 {
+ gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_pwm0: gpio-pwm0 {
+ compatible = "pwm-gpio";
+ gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&gpio_pwm0_pin>;
+ pinctrl-names = "default";
+ #pwm-cells = <3>;
+ };
+
+ vbus5v0_typec: regulator-vbus5v0-typec {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus5v0_typec";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio0 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc5v0_device>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg0_pwren>;
+ };
+
+ vcc12v_dcin: regulator-vcc12v-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc12v_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc1v2_ufs_vccq_s0: regulator-vcc1v2-ufs-vccq-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v2_ufs_vccq_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc1v8_ufs_vccq2_s0: regulator-vcc1v8-ufs-vccq2-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc1v8_ufs_vccq2_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
+
+ vcc3v3_lcd_n: regulator-vcc3v3-lcd0-n {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_lcd0_n";
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc_3v3_s0>;
+ };
+
+ vcc3v3_pcie1: regulator-vcc3v3-pcie1 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_pcie1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <5000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc3v3_rtc_s5: regulator-vcc3v3-rtc-s5 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_rtc_s5";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc5v0_device: regulator-vcc5v0-device {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_device";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc5v0_host: regulator-vcc5v0-host {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_host";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&vcc5v0_device>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren>;
+ };
+
+ vcc_sys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc12v_dcin>;
+ };
+
+ vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_1v8_s0: regulator-vcc-1v8-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
+
+ vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_2v0_pldo_s3";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_3v3_s0: regulator-vcc-3v3-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_s3>;
+ };
+
+ vcc3v3_sd: regulator-vcc-3v3-sd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwren>;
+ regulator-name = "vcc3v3_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_s0>;
+ };
+
+ vcc_ufs_s0: regulator-vcc-ufs-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_ufs_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_wifi_reg_on: regulator-wifi-reg-on {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&wifi_reg_on>;
+ pinctrl-names = "default";
+ regulator-name = "wifi_reg_on";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_det>;
+ simple-audio-card,name = "On-board Analog ES8388";
+ simple-audio-card,aux-devs = <&hp_power>, <&spk_power>;
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,pin-switches = "Headphones", "Speaker", "Main Mic", "Headset Mic";
+ simple-audio-card,routing =
+ "Headphone Power INL", "LOUT1",
+ "Headphone Power INR", "ROUT1",
+ "Speaker Power INL", "LOUT2",
+ "Speaker Power INR", "ROUT2",
+ "Headphones", "Headphone Power OUTL",
+ "Headphones", "Headphone Power OUTR",
+ "Speaker", "Speaker Power OUTL",
+ "Speaker", "Speaker Power OUTR",
+ "LINPUT1", "Main Mic",
+ "LINPUT2", "Main Mic",
+ "RINPUT1", "Headset Mic",
+ "RINPUT2", "Headset Mic";
+ simple-audio-card,widgets =
+ "Microphone", "Main Mic",
+ "Microphone", "Headset Mic",
+ "Headphone", "Headphones",
+ "Speaker", "Speaker";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai1>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ hp_power: headphone-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_ctl>;
+ sound-name-prefix = "Headphone Power";
+ };
+
+ spk_power: speaker-amplifier {
+ compatible = "simple-audio-amplifier";
+ enable-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spk_ctl>;
+ sound-name-prefix = "Speaker Power";
+ VCC-supply = <&vcc5v0_device>;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy1_psu {
+ status = "okay";
+};
+
+&edp {
+ status = "okay";
+ pinctrl-names = "default";
+ /*
+ * Please check the switch of GPIO4_C1, it may not be switched to
+ * eDP HPD function by default.
+ */
+ pinctrl-0 = <&edp_txm0_pins>;
+ // pinctrl-0 = <&edp0_hpd>;
+ // hpd-gpios = <&gpio4 RK_PC1 GPIO_ACTIVE_HIGH>;
+};
+
+// &pinctrl {
+// edp {
+// edp0_hpd: edp0-hpd {
+// rockchip,pins = <4 RK_PC1 0 &pcfg_pull_none>;
+// };
+// };
+// };
+
+&edp_in {
+ edp_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_edp>;
+ };
+};
+
+&edp_out {
+ edp_out_conn: endpoint {
+ remote-endpoint = <&dp_con_in>;
+ };
+};
+
+&gmac0 {
+ clock_in_out = "output";
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&rgmii_phy0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð0m0_miim
+ ð0m0_tx_bus2
+ ð0m0_rx_bus2
+ ð0m0_rgmii_clk
+ ð0m0_rgmii_bus
+ ðm0_clk0_25m_out>;
+ tx_delay = <0x21>;
+ status = "okay";
+};
+
+&gmac1 {
+ clock_in_out = "output";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-rxid";
+ pinctrl-names = "default";
+ pinctrl-0 = <ð1m0_miim
+ ð1m0_tx_bus2
+ ð1m0_rx_bus2
+ ð1m0_rgmii_clk
+ ð1m0_rgmii_bus
+ ðm0_clk1_25m_out>;
+ tx_delay = <0x20>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ status = "okay";
+};
+
+&hdmi {
+ status = "disabled";
+};
+
+&hdmi_sound {
+ status = "disabled";
+};
+
+&hdptxphy {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk806: pmic@23 {
+ compatible = "rockchip,rk806";
+ reg = <0x23>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ system-power-controller;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&vcc_sys>;
+ vcc10-supply = <&vcc_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc_sys>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs1_slp: dvs1-slp-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs1_pwrdn: dvs1-pwrdn-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs1_rst: dvs1-rst-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_slp: dvs2-slp-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs2_pwrdn: dvs2-pwrdn-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs2_rst: dvs2-rst-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs2_dvs: dvs2-dvs-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs2_gpio: dvs2-gpio-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun5";
+ };
+
+ rk806_dvs3_slp: dvs3-slp-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun1";
+ };
+
+ rk806_dvs3_pwrdn: dvs3-pwrdn-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun2";
+ };
+
+ rk806_dvs3_rst: dvs3-rst-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun3";
+ };
+
+ rk806_dvs3_dvs: dvs3-dvs-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun4";
+ };
+
+ rk806_dvs3_gpio: dvs3-gpio-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun5";
+ };
+
+ regulators {
+ vdd_cpu_big_s0: dcdc-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_cpu_big_s0";
+ regulator-enable-ramp-delay = <400>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_s0: dcdc-reg2 {
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_s0";
+ regulator-enable-ramp-delay = <400>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: dcdc-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_cpu_lit_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_3v3_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd_gpu_s0: dcdc-reg5 {
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_s0";
+ regulator-enable-ramp-delay = <400>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vddq_ddr_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_logic_s0: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <800000>;
+ regulator-name = "vdd_logic_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd2_ddr_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_ddr_s0: dcdc-reg10 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd_ddr_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca_1v8_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pldo2_s0: pldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pldo2_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_1v2_s0: pldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdda_1v2_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca_3v3_s0: pldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcca_3v3_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pldo6_s3: pldo-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pldo6_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s3";
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdda_ddr_pll_s0: nldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdda_ddr_pll_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v75_hdmi_s0: nldo-reg3 {
+ regulator-boot-on;
+ regulator-min-microvolt = <837500>;
+ regulator-max-microvolt = <837500>;
+ regulator-name = "vdda0v75_hdmi_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v85_s0: nldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdda_0v85_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v75_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdda_0v75_s0";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ clock-output-names = "hym8563";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA0 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtc_int>;
+ wakeup-source;
+ #clock-cells = <0>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ es8388: audio-codec@10 {
+ compatible = "everest,es8388", "everest,es8328";
+ reg = <0x10>;
+ AVDD-supply = <&vcca_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcca_3v3_s0>;
+ PVDD-supply = <&vcc_1v8_s0>;
+ assigned-clocks = <&cru CLK_SAI1_MCLKOUT_TO_IO>;
+ assigned-clock-rates = <12288000>;
+ clocks = <&cru CLK_SAI1_MCLKOUT_TO_IO>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sai1m0_mclk>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ clocks = <&cru REFCLKO25M_GMAC0_OUT>;
+ assigned-clocks = <&cru REFCLKO25M_GMAC0_OUT>;
+ assigned-clock-rates = <25000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_phy0_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ clocks = <&cru REFCLKO25M_GMAC1_OUT>;
+ assigned-clocks = <&cru REFCLKO25M_GMAC1_OUT>;
+ assigned-clock-rates = <25000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_phy1_rst>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_rst>;
+ reset-gpios = <&gpio2 RK_PB4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_s3>;
+ status = "okay";
+
+ pcie@0,0 {
+ reg = <0x0 0 0 0 0>;
+ bus-range = <0x0 0xf>;
+ device_type = "pci";
+ ranges;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ wifi: wifi@0,0 {
+ compatible = "pci14e4,449d";
+ reg = <0x10000 0 0 0 0>;
+ clocks = <&hym8563>;
+ clock-names = "lpo";
+ };
+ };
+};
+
+&pcie1 {
+ reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie1>;
+
+ /*
+ * Disable usb_drd1_dwc3 if enabling pcie1 and set Dial_Switch_1
+ * to low state according to the schematic of page 17.
+ */
+ status = "disabled";
+};
+
+&pinctrl {
+ gpio_pwm0 {
+ gpio_pwm0_pin: gpio-pwm0-pin {
+ rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ audio {
+ hp_det: hp-det {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ hp_ctl: hp-ctl {
+ rockchip,pins = <3 RK_PD6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ spk_ctl: spk-ctl {
+ rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ bluetooth {
+ bt_reg_on: bt-reg-on {
+ rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ bt_wake_host: bt-wake-host {
+ rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ host_wake_bt: host-wake-bt {
+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ hdmi {
+ hdmi_tx_on_h: hdmi-tx-on-h {
+ rockchip,pins = <2 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ hym8563 {
+ rtc_int: rtc-int {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ network {
+ rgmii_phy0_rst: rgmii-phy0-rst {
+ rockchip,pins = <2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ rgmii_phy1_rst: rgmii-phy1-rst {
+ rockchip,pins = <3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie0 {
+ pcie0_rst: pcie0-rst {
+ rockchip,pins = <2 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_pwren: sdmmc-pwren {
+ rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ usb_host_pwren: usb-host-pwren {
+ rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_otg0_pwren: usb-otg0-pwren {
+ rockchip,pins = <0 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usbc0_int: usbc0-int {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on: wifi-reg-on {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ wifi_wake_host: wifi-wake-host {
+ rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&sai1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sai1m0_lrck
+ &sai1m0_sclk
+ &sai1m0_sdi0
+ &sai1m0_sdo0>;
+ status = "okay";
+};
+
+&sai6 {
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ full-pwr-cycle-in-suspend;
+ max-frequency = <200000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ no-sdio;
+ no-sd;
+ non-removable;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <200000000>;
+ no-sdio;
+ no-mmc;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_det &sdmmc0_bus4>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8_s0>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vbus5v0_typec>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ clocks = <&hym8563>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB1 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-0 = <&bt_reg_on &bt_wake_host &host_wake_bt>;
+ pinctrl-names = "default";
+ shutdown-gpios = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <&vcc_3v3_s3>;
+ vddio-supply = <&vcc_1v8_s3>;
+ };
+};
+
+&ufshc {
+ status = "okay";
+};
+
+&usbdp_phy {
+ rockchip,dp-lane-mux = <2 3>;
+ status = "okay";
+};
+
+&usb_drd0_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_drd1_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_edp: endpoint@ROCKCHIP_VOP2_EP_EDP0 {
+ reg = <ROCKCHIP_VOP2_EP_EDP0>;
+ remote-endpoint = <&edp_in_vp0>;
+ };
+};
--
2.34.1