Re: [PATCH] media: mc: Remove spurious WARN_ON in __media_pipeline_start

[Niharika Khare]

On Fri, Aug 21, 2026 at 09:33:26PM +0200, Laurent Pinchart wrote:
> On Fri, Aug 21, 2026 at 10:28:07PM +0530, Niharika Khare wrote:
> > Vimc driver's entity topology has three capture nodes and two of
> > those (Raw Capture 0 and RGB/YUV Capture) are reachable from each
> > other via enabled links. The crash report and the C repro show that
> > the two capture nodes attempt to invoke a STREAMON session one after
> > the other, which resulted in the WARNING getting triggered by the
> > media controller.
> > 
> >   vimc link validate: Sensor A:src:640x480 (0x42474752, 0, 0, 0, 0) Raw Capture 0:snk:640x480 (0x42474752, 8, 0, 0, 0)
> >   vimc link validate: Scaler:src:640x480 (0x33424752, 8, 0, 0, 0) RGB/YUV Capture:snk:640x480 (0x33424752, 8, 0, 0, 0)
> >   origin->pipe && origin->pipe != pipe
> >   WARNING: drivers/media/mc/mc-entity.c:785 at __media_pipeline_start+0x1add/0x22b0, CPU#1: syz.0.17/5912
> > 
> > The graph walk originating from Raw Capture 0 (first STREAMON in C
> > repro on /dev/video0) reaches RGB/YUV Capture and marks its origin
> > pad's pipe with its own pipe. When RGB/YUV Capture's graph walk starts
> > (second STREAMON in C repro on /dev/video4), the pad is already
> > claimed. This is a legitimate userspace request but not something that
> 
> No, that's not supposed to be a legitimate use case. The WARN_ON
> indicates a driver bug.

Thanks for the direction Laurent, I'll look into vimc's architecture to
check on how the two capture nodes ended up starting the pipeline back
to back.

> > kernel should allow while the pad remains claimed. Hence, the kernel
> > checks the pipe and returns -EBUSY instead of raising a bug, same as
> > the other non-origin pads. The check on origin pad's pipe needs to stay
> > otherwise the origin pad case would go through the increment on the
> > start_count path, even though there exists a loop few lines below this
> > block to check the pad and return -EBUSY. The check also provides early
> > failure detection and prevents the complete graph walk.
> > 
> > Fixes: ae219872834a ("media: mc: entity: Rewrite media_pipeline_start()")
> > Reported-by: syzbot+68e901d044baaea1f60c@xxxxxxxxxxxxxxxxxxxxxxxxx
> > Closes: https://syzkaller.appspot.com/bug?extid=68e901d044baaea1f60c
> > Tested-by: syzbot+68e901d044baaea1f60c@xxxxxxxxxxxxxxxxxxxxxxxxx
> > Signed-off-by: Niharika Khare <niharikakhare2101@xxxxxxxxx>
> > ---
> >  drivers/media/mc/mc-entity.c | 18 ++++++++++++------
> >  1 file changed, 12 insertions(+), 6 deletions(-)
> > 
> > diff --git a/drivers/media/mc/mc-entity.c b/drivers/media/mc/mc-entity.c
> > index 3fa0bc687..7b4ef2c95 100644
> > --- a/drivers/media/mc/mc-entity.c
> > +++ b/drivers/media/mc/mc-entity.c
> > @@ -778,12 +778,18 @@ __must_check int __media_pipeline_start(struct media_pad *origin,
> >  
> >  	lockdep_assert_held(&mdev->graph_mutex);
> >  
> > -	/*
> > -	 * If the pad is already part of a pipeline, that pipeline must be the
> > -	 * same as the pipe given to media_pipeline_start().
> > -	 */
> > -	if (WARN_ON(origin->pipe && origin->pipe != pipe))
> > -		return -EINVAL;
> > +	/*
> > +	 * If the pad is part of a different pipeline than the one passed on to
> > +	 * media_pipeline_start(), the pad must wait for the ongoing session on
> > +	 * this previous pipeline to complete before it starts a new session.
> > +	 * The request for starting the pipeline, although valid, cannot be
> > +	 * served until the ongoing request finishes.
> > +	 */
> > +	if (origin->pipe && origin->pipe != pipe) {
> > +		dev_dbg(mdev->dev, "Failed to start pipeline: pad '%s':%u busy\n",
> > +			origin->entity->name, origin->index);
> > +		return -EBUSY;
> > +	}
> >  
> >  	/*
> >  	 * If the pipeline has already been started, it is guaranteed to be
> 
> -- 
> Regards,
> 
> Laurent Pinchart

Regards,

Niharika Khare