Re: [PATCH v6 5/6] iio: pressure: dps310: add hardware FIFO support

[Andy Shevchenko]

On Mon, Aug 24, 2026 at 11:12:02PM +0300, Rupesh Majhi wrote:
> Use the 32 entry FIFO for buffered capture, so a reader wakes once per

When referring to the size, use dash: 32-entry

> batch of samples instead of once per sample.

> FIFO runs when no trigger is attached and stays off when one is.
> iio_verify_update() already picks the mode, so buffer setup ops just
> branch on iio_device_get_current_mode(), as rohm-bm1390.c does.
> 
> Drain is on a timer because there is no interrupt to use and nothing in

"Drain is on a timer..." --> What is this supposed to mean?

> tree wires the INT pin. hwfifo_flush_to_buffer is not enough on its own:

"The .hwfifo_flush_to_buffer()..."

> iio_buffer_read() sleeps until something is pushed, so a blocking reader
> would hang with samples still sitting in the FIFO. Hook is kept for
> poll() and non-blocking reads.
> 
> Pressure entries drive the scans and reuse last temperature, so the two
> configured rates stay independent. FIFO does not timestamp entries, they
> are estimated from the sample rate.

...

> +/*
> + * Bounds on the drain interval. The lower bound keeps a fast rate from
> + * flooding the workqueue; the upper bound keeps the FIFO from filling while
> + * nothing is looking at it.
> + */
> +#define DPS310_DRAIN_MIN_MS	20
> +#define DPS310_DRAIN_MAX_MS	2000

2 * MSEC_PER_SEC

> +
>  /* Make sure sleep time is <= 30ms for usleep_range */
>  #define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)

30 * USEC_PER_MSEC

...

> struct dps310_data {

Run `pahole` and check if there are gaps to fill. In such a case think if it
would make sense to shuffle a bit the added fields to make the structure more
compact.

>  	s32 pressure_raw;
>  	s32 temp_raw;
>  	bool timeout_recovery_failed;
> +
> +	/* FIFO capture state, used only while the hardware FIFO is enabled */
> +	struct iio_dev *iio;
> +	struct delayed_work fifo_work;
> +	unsigned int watermark;
> +	unsigned int drain_interval_ms;
> +	s64 fifo_timestamp;
> +	s32 fifo_temp_raw;
> +	bool fifo_temp_valid;
>  };

...

> +static int dps310_fifo_set_enable(struct dps310_data *data, bool enable)
> +	__must_hold(&data->lock)
> +{
> +	return regmap_write_bits(data->regmap, DPS310_CFG_REG, DPS310_FIFO_EN,
> +				 enable ? DPS310_FIFO_EN : 0);

_assign_bits()?

> +}

...

> +/*
> + * There is no interrupt wired on any in-tree platform and the binding has no
> + * interrupts property, so the FIFO is drained on a timer, at an interval below
> + * the time it takes to fill. See DPS310_FIFO_DEPTH for why late is bad.
> + */
> +static int dps310_fifo_interval(struct dps310_data *data, unsigned int *ms)
> +	__must_hold(&data->lock)
> +{
> +	bool pressure_enabled = test_bit(DPS310_SCAN_PRESSURE,
> +					 data->iio->active_scan_mask);
> +	unsigned int fill_ms, want_ms;
> +	int rc, prs_rate, tmp_rate;

Can _rate:s be negative?

> +	rc = dps310_get_pres_samp_freq(data, &prs_rate);
> +	if (rc)
> +		return rc;
> +
> +	rc = dps310_get_temp_samp_freq(data, &tmp_rate);
> +	if (rc)
> +		return rc;
> +
> +	/* Both streams share the same entries, so they fill it together. */
> +	fill_ms = MSEC_PER_SEC * DPS310_FIFO_DEPTH / (prs_rate + tmp_rate);
> +
> +	/*
> +	 * The DPS310 has no configurable hardware watermark, only a FIFO-full
> +	 * condition, so the watermark is taken as the number of scans the user
> +	 * is prepared to wait for and drives the drain interval instead. Scans
> +	 * come at the rate of whichever measurement drives them, which is not
> +	 * the pressure rate when only the temperature channel is enabled.
> +	 */
> +	want_ms = data->watermark * MSEC_PER_SEC /
> +		  (pressure_enabled ? prs_rate : tmp_rate);

With plain if-else this becomes more readable.

> +	*ms = clamp(min(want_ms, fill_ms / 2), DPS310_DRAIN_MIN_MS,
> +		    DPS310_DRAIN_MAX_MS);
> +
> +	return 0;
> +}

...

> +/*
> + * Read a single FIFO entry. Returns 1 if a sample was read, 0 once the FIFO is
> + * empty, or a negative error.
> + */
> +static int dps310_fifo_read_entry(struct dps310_data *data, s32 *value,
> +				  bool *is_pressure)

Instead of using this boolean, use return 1 or return 2.

> +	__must_hold(&data->lock)
> +{
> +	u8 val[3];
> +	s32 raw;
> +	int rc;
> +
> +	/*
> +	 * Every entry is read through the pressure registers regardless of
> +	 * which measurement produced it, with the type tagged in the LSB.
> +	 */
> +	rc = regmap_bulk_read(data->regmap, DPS310_PRS_BASE, val, sizeof(val));
> +	if (rc < 0)
> +		return rc;
> +
> +	raw = get_unaligned_be24(val);
> +	if (raw == DPS310_FIFO_EMPTY_VAL)
> +		return 0;
> +
> +	*is_pressure = raw & DPS310_FIFO_TAG_PRS;
> +	*value = sign_extend32(raw, 23);
> +
> +	return 1;
> +}

...

> +static int dps310_fifo_push_scan(struct dps310_data *data, s32 temp_raw,
> +				 s32 pressure_raw, s64 timestamp)
> +	__must_hold(&data->lock)
> +{
> +	struct iio_dev *iio = data->iio;
> +	struct dps310_scan scan = { };

> +	int i = 0;

Same comments as earlier in the series.

> +	int rc;
> +
> +	/*
> +	 * The compensation helpers read the cached raw values. Sysfs reads take
> +	 * the direct-mode claim, so they cannot be looking at these while a
> +	 * buffered capture is running.
> +	 */
> +	data->temp_raw = temp_raw;
> +	data->pressure_raw = pressure_raw;
> +
> +	if (test_bit(DPS310_SCAN_TEMP, iio->active_scan_mask)) {
> +		rc = dps310_calculate_temp(data, &scan.channels[i]);
> +		if (rc)
> +			return rc;
> +
> +		i++;
> +	}
> +
> +	if (test_bit(DPS310_SCAN_PRESSURE, iio->active_scan_mask)) {
> +		rc = dps310_calculate_pressure(data, &scan.channels[i]);
> +		if (rc)
> +			return rc;
> +	}
> +
> +	iio_push_to_buffers_with_ts(iio, &scan, sizeof(scan), timestamp);
> +
> +	return 0;
> +}

...

I stopped here, I think you should understand what this code is all doing. Now
it's an AI mess. Split this patch to a few smaller ones each of them you understand.

-- 
With Best Regards,
Andy Shevchenko