Re: [PATCH v2 2/3] dt-bindings: pinctrl: Add EcoNet EN7528 pin controller

[Ahmed Naseef]

On Fri, Aug 28, 2026 at 04:51:27PM +0100, Conor Dooley wrote:
> On Fri, Aug 28, 2026 at 07:35:14PM +0400, Ahmed Naseef wrote:
> > Add the binding for the pin controller found on the EcoNet EN7528 MIPS
> > SoC. It shares the IP with the Airoha pin controllers, but its IOMUX and
> > pin configuration registers have a different layout, so it gets its own
> > compatible.
> > 
> > The CHIP SCU holding those registers is referenced by the airoha,chip-scu
> > phandle.
> > 
> > Signed-off-by: Ahmed Naseef <naseefkm@xxxxxxxxx>
> > ---
> >  .../pinctrl/econet,en7528-pinctrl.yaml        | 190 ++++++++++++++++++
> >  1 file changed, 190 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pinctrl/econet,en7528-pinctrl.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/pinctrl/econet,en7528-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/econet,en7528-pinctrl.yaml
> > new file mode 100644
> > index 000000000000..3ce1a5309d09
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/econet,en7528-pinctrl.yaml
> > @@ -0,0 +1,190 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pinctrl/econet,en7528-pinctrl.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: EcoNet EN7528 Pin Controller
> > +
> > +maintainers:
> > +  - Lorenzo Bianconi <lorenzo@xxxxxxxxxx>
> > +
> > +description:
> > +  The EcoNet EN7528 pin controller is used to control SoC pins. It shares the
> > +  IP with the Airoha pin controllers, but its IOMUX and pin configuration
> > +  registers have a different layout.
> > +
> > +properties:
> > +  compatible:
> > +    const: econet,en7528-pinctrl
> > +
> > +  airoha,chip-scu:
> > +    description: phandle to the chip SCU syscon
> > +    $ref: /schemas/types.yaml#/definitions/phandle
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  gpio-controller: true
> > +
> > +  '#gpio-cells':
> > +    const: 2
> > +
> > +  gpio-ranges:
> > +    maxItems: 1
> > +
> > +  interrupt-controller: true
> > +
> > +  '#interrupt-cells':
> > +    const: 2
> > +
> > +patternProperties:
> > +  '-pins$':
> > +    type: object
> > +
> > +    patternProperties:
> > +      '^mux(-|$)':
> > +        type: object
> > +
> > +        description:
> > +          pinmux configuration nodes.
> > +
> > +        $ref: /schemas/pinctrl/pinmux-node.yaml
> > +
> > +        properties:
> > +          function:
> > +            description:
> > +              A string containing the name of the function to mux to the group.
> > +            enum: [gpio, jtag, pcie_reset, pcm, pcm_spi, phy1_led0,
> > +                   phy1_led1, phy2_led0, phy2_led1, phy3_led0, phy3_led1,
> > +                   phy4_led0, phy4_led1, pnand, pon, pwm, sipo, spi, uart]
> > +
> > +          groups:
> > +            description:
> > +              An array of strings. Each string contains the name of a group.
> > +            items:
> > +              enum: [pon, sipo, sipo_rclk, uart2, uart2_cts_rts, uart3,
> > +                     ejtag, pcm1, pcm2, spi_quad, spi_cs1, pcm_spi,
> > +                     pcm_spi_int, pcm_spi_rst, pcm_spi_cs1, pcm_spi_cs2,
> > +                     pcm_spi_cs3, pcm_spi_cs4, pcm_spi_cs5, pcm_spi_cs6,
> > +                     pcm_spi_cs7, pnand, gpio0, gpio1, gpio2, gpio3, gpio4,
> > +                     gpio5, gpio6, gpio7, gpio8, gpio9, gpio10, gpio11,
> > +                     gpio12, gpio13, gpio14, gpio15, gpio16, gpio17,
> > +                     gpio18, gpio19, gpio20, gpio21, gpio22, gpio23,
> > +                     gpio24, gpio25, gpio26, gpio27, gpio28, gpio29,
> > +                     gpio30, gpio31, gpio32, gpio33, gpio34, gpio35,
> > +                     gpio36, gpio37, gpio38, gpio39, gpio40, gpio41,
> > +                     pcie_reset0, pcie_reset1]
> > +
> > +        required:
> > +          - function
> > +          - groups
> > +
> > +        additionalProperties: false
> > +
> > +      '^conf(-|$)':
> 
> Why is this needed? Why can you not tell from the group which pins the
> config applies to?

Not for all of them: i2c_sda, i2c_scl, uart_txd and uart_rxd are in no
group at all. The spi_cs0/clk/mosi/miso pads are only in pnand, which is
17 pins wide, so no group names them individually either.

Ahmed


> 
> Thanks,
> Conor.
> 
> > +        type: object
> > +
> > +        description:
> > +          pinconf configuration nodes.
> > +
> > +        $ref: /schemas/pinctrl/pincfg-node.yaml
> > +
> > +        properties:
> > +          pins:
> > +            description:
> > +              An array of strings. Each string contains the name of a pin.
> > +            items:
> > +              enum: [gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6,
> > +                     gpio7, gpio8, gpio9, gpio10, gpio11, gpio12, gpio13,
> > +                     gpio14, gpio15, gpio16, gpio17, gpio18, gpio19,
> > +                     gpio20, gpio21, gpio22, gpio23, gpio24, gpio25,
> > +                     gpio26, gpio27, gpio28, gpio29, gpio30, gpio31,
> > +                     gpio32, gpio33, gpio34, gpio35, gpio36, gpio37,
> > +                     gpio38, gpio39, pcie_reset0, pcie_reset1, i2c_sda,
> > +                     i2c_scl, uart_txd, uart_rxd, spi_cs0, spi_clk,
> > +                     spi_mosi, spi_miso]
> > +            minItems: 1
> > +            maxItems: 50
> > +
> > +          bias-disable: true
> > +
> > +          bias-pull-up: true
> > +
> > +          bias-pull-down: true
> > +
> > +          input-enable: true
> > +
> > +          output-enable: true
> > +
> > +          output-low: true
> > +
> > +          output-high: true
> > +
> > +          drive-strength:
> > +            description:
> > +              Selects the drive strength for the pin, in mA.
> > +            enum: [2, 4]
> > +
> > +        required:
> > +          - pins
> > +
> > +        additionalProperties: false
> > +
> > +    additionalProperties: false
> > +
> > +required:
> > +  - compatible
> > +  - airoha,chip-scu
> > +  - interrupts
> > +  - gpio-controller
> > +  - gpio-ranges
> > +  - "#gpio-cells"
> > +  - interrupt-controller
> > +  - "#interrupt-cells"
> > +
> > +allOf:
> > +  - $ref: pinctrl.yaml#
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/interrupt-controller/mips-gic.h>
> > +    #include <dt-bindings/interrupt-controller/irq.h>
> > +
> > +    pinctrl {
> > +      compatible = "econet,en7528-pinctrl";
> > +
> > +      airoha,chip-scu = <&chip_scu>;
> > +
> > +      interrupt-parent = <&gic>;
> > +      interrupts = <GIC_SHARED 10 IRQ_TYPE_LEVEL_HIGH>;
> > +
> > +      gpio-controller;
> > +      #gpio-cells = <2>;
> > +
> > +      interrupt-controller;
> > +      #interrupt-cells = <2>;
> > +
> > +      gpio-ranges = <&pinctrl 0 0 42>;
> > +
> > +      uart2-pins {
> > +        mux {
> > +          function = "uart";
> > +          groups = "uart2";
> > +        };
> > +
> > +        conf {
> > +          pins = "gpio28", "gpio29";
> > +          bias-pull-up;
> > +        };
> > +      };
> > +
> > +      pwm-pins {
> > +        mux {
> > +          function = "pwm";
> > +          groups = "gpio30";
> > +        };
> > +      };
> > +    };
> > -- 
> > 2.34.1
> >