[PATCH 6/6] arm64: dts: qcom: sc8280xp: add Radxa Dragon Q8B
From: Xilin Wu
Date: Tue Sep 01 2026 - 04:55:44 EST
Add initial device tree support for the Radxa Dragon Q8B,
a single-board computer based on the Qualcomm Snapdragon 8cx Gen 3
SC8280XP platform.
Describe the following hardware:
- UFS and microSD storage
- Two M.2 M-key PCIe connectors
- An M.2 E-key connector for Wi-Fi and Bluetooth
- The QPS615 PCIe switch and its downstream topology
- Two USB-C ports with DisplayPort alternate mode
- USB Type-A ports
- HDMI 2.1 output through the Chrontel CH7218A bridge
- WCD9385 headset audio
- GPU, video, ADSP and CDSP remote processors
- RTC, EEPROM, thermal sensors and the 40-pin expansion header
Co-developed-by: Stephen Chen <stephen@xxxxxxxxx>
Signed-off-by: Stephen Chen <stephen@xxxxxxxxx>
Co-developed-by: Junhao Xie <bigfoot@xxxxxxxxx>
Signed-off-by: Junhao Xie <bigfoot@xxxxxxxxx>
Signed-off-by: Xilin Wu <sophon@xxxxxxxxx>
---
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../boot/dts/qcom/sc8280xp-radxa-dragon-q8b.dts | 2097 ++++++++++++++++++++
2 files changed, 2099 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..34244354ba75 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -299,6 +299,8 @@ sc8280xp-microsoft-arcata-el2-dtbs := sc8280xp-microsoft-arcata.dtb sc8280xp-el2
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-arcata.dtb sc8280xp-microsoft-arcata-el2.dtb
sc8280xp-microsoft-blackrock-el2-dtbs := sc8280xp-microsoft-blackrock.dtb sc8280xp-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-blackrock.dtb sc8280xp-microsoft-blackrock-el2.dtb
+sc8280xp-radxa-dragon-q8b-el2-dtbs := sc8280xp-radxa-dragon-q8b.dtb sc8280xp-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-radxa-dragon-q8b.dtb sc8280xp-radxa-dragon-q8b-el2.dtb
dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm450-lenovo-tbx605f.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm450-motorola-ali.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-radxa-dragon-q8b.dts b/arch/arm64/boot/dts/qcom/sc8280xp-radxa-dragon-q8b.dts
new file mode 100644
index 000000000000..1c0e94bba4d7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-radxa-dragon-q8b.dts
@@ -0,0 +1,2097 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Radxa Computer (Shenzhen) Co., Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/delete-node/ &pil_video_mem;
+/delete-node/ &pil_nsp1_mem;
+/delete-node/ &remoteproc_nsp1;
+
+/ {
+ model = "Radxa Dragon Q8B";
+ compatible = "radxa,dragon-q8b", "qcom,sc8280xp";
+ chassis-type = "embedded";
+
+ aliases {
+ serial0 = &uart17;
+ serial1 = &uart2;
+ };
+
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_s10b>;
+ vdd-rxtx-supply = <&vreg_s10b>;
+ vdd-io-supply = <&vreg_s10b>;
+ vdd-mic-bias-supply = <&vreg_bob>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ qcom,hphl-jack-type-normally-closed;
+
+ #sound-dai-cells = <1>;
+ };
+
+ hdmi-bridge {
+ compatible = "chrontel,ch7218a";
+
+ vdd-supply = <&vcc_5v_s>;
+
+ pinctrl-0 = <&dp_hpd_default>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_bridge_dp_in: endpoint {
+ remote-endpoint = <&mdss0_dp2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_bridge_frl_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&hdmi_bridge_frl_out>;
+ };
+ };
+ };
+
+ iio-hwmon {
+ compatible = "iio-hwmon";
+ io-channels = <&adp12v_voltage 0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&user_led>;
+ pinctrl-names = "default";
+
+ user-led {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ nvme-connector {
+ compatible = "pcie-m2-m-connector";
+ vpcie3v3-supply = <&vcc_nvme_3v3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nvme_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&pcie2a_ep>;
+ };
+ };
+ };
+ };
+
+ nvme2-connector {
+ compatible = "pcie-m2-m-connector";
+ vpcie3v3-supply = <&vcc_nvme2_3v3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ nvme2_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&pcie3b_ep>;
+ };
+ };
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 166 GPIO_ACTIVE_HIGH>,
+ <&tlmm 49 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con0_hs: endpoint {
+ remote-endpoint = <&usb_0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con0_ss: endpoint {
+ remote-endpoint = <&usb_0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con0_sbu: endpoint {
+ remote-endpoint = <&usb0_sbu_mux>;
+ };
+ };
+ };
+ };
+
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con1_hs: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con1_ss: endpoint {
+ remote-endpoint = <&usb_1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con1_sbu: endpoint {
+ remote-endpoint = <&usb1_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ vcc_1v8: regulator-vcc-1v8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8a>;
+
+ gpio = <&tlmm 161 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ /* Longer delay for I2C pull-up to stabilize */
+ startup-delay-us = <50000>;
+
+ pinctrl-0 = <&vcc_1v8_reg_en>;
+ pinctrl-names = "default";
+ };
+
+ vcc_1v8a: regulator-vcc-1v8a {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_1v8a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pmc8280c_gpios 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ startup-delay-us = <1000>;
+
+ pinctrl-0 = <ð_phy_pwr_en>;
+ pinctrl-names = "default";
+ };
+
+ vcc_3v3_ekey: regulator-vcc-3v3-ekey {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_3v3_ekey";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmr735a_gpios 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <3000>;
+
+ pinctrl-0 = <&hastings_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vcc_5v_s: regulator-vcc-5v-s {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_5v_s";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&tlmm 159 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <250000>;
+ off-on-delay-us = <150000>;
+
+ pinctrl-0 = <&vcc_5v_s_reg_en>;
+ pinctrl-names = "default";
+
+ /* CH7218A needs to be powered on for HPD logic to work */
+ regulator-always-on;
+ };
+
+ vcc_nvme_3v3: regulator-vcc-nvme-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_nvme_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <1500>;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+ };
+
+ vcc_nvme2_3v3: regulator-vcc-nvme2-3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vcc_nvme2_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 158 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <1500>;
+
+ pinctrl-0 = <&nvme2_reg_en>;
+ pinctrl-names = "default";
+ };
+
+ /* This regulator is actually part of the UFS module */
+ vcc_ufs: regulator-vcc-ufs {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_ufs";
+ regulator-min-microvolt = <2480000>;
+ regulator-max-microvolt = <2480000>;
+ vin-supply = <&vreg_l7d>;
+ };
+
+ vdd_ntn_core_0p9: regulator-vdd-ntn-core-0p9 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd_ntn_core_0p9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ gpio = <&tlmm 160 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <1000>;
+
+ pinctrl-0 = <&ntn_0p9_en>;
+ pinctrl-names = "default";
+ };
+
+ vdd_usb2: regulator-vdd-usb2 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd_usb2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&pmc8280c_gpios 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <700>;
+
+ pinctrl-0 = <&usb2_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_usb3: regulator-vdd-usb3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd_usb3";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&pmc8280c_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <700>;
+
+ pinctrl-0 = <&usb3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ linux,cma {
+ compatible = "shared-dma-pool";
+ size = <0x0 0x8000000>;
+ reusable;
+ linux,cma-default;
+ };
+
+ pil_video_mem: video-region@8c600000 {
+ reg = <0 0x8c600000 0 0x700000>;
+ no-map;
+ };
+ };
+
+ thermal-zones {
+ eeprom-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 2>;
+ };
+
+ led-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 6>;
+ };
+
+ left-edge-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 5>;
+ };
+
+ left-edge-2-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 7>;
+ };
+
+ pmc8280c-thermal {
+ cooling-maps {
+ map0 {
+ trip = <&pmc8280c_alert0>;
+ /* Throttle X1C cores to 2496MHz at 105C */
+ cooling-device = <&cpu4 5 5>,
+ <&cpu5 5 5>,
+ <&cpu6 5 5>,
+ <&cpu7 5 5>;
+ };
+ };
+
+ trips {
+ pmc8280c_alert0: trip2 {
+ temperature = <105000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+ };
+ };
+
+ smb2351-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 3>;
+ };
+
+ top-left-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 0>;
+ };
+
+ top-right-thermal {
+ thermal-sensors = <&pmk8280_adc_tm 1>;
+ };
+
+ vbat-thermal {
+ polling-delay-passive = <250>;
+ thermal-sensors = <&pmk8280_adc_tm 4>;
+
+ cooling-maps {
+ map0 {
+ trip = <&vbat_alert1>;
+ cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ vbat_alert0: trip-point0 {
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ vbat_alert1: trip-point1 {
+ temperature = <80000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ vbat_crit: vbat-crit {
+ temperature = <105000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
+ usb0-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb0_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb0_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con0_sbu>;
+ };
+ };
+ };
+
+ usb1-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb1_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb1_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con1_sbu>;
+ };
+ };
+ };
+
+ adp12v_voltage: voltage-divider-adp12v {
+ compatible = "voltage-divider";
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM5(1)>;
+ #io-channel-cells = <1>;
+
+ /* R470 (110K) in series with R471 (10K) to ground. */
+ full-ohms = <120000>;
+ output-ohms = <10000>;
+ };
+
+ wlan-connector {
+ compatible = "pcie-m2-e-connector";
+
+ vpcie3v3-supply = <&vcc_3v3_ekey>;
+ vpcie1v8-supply = <&vreg_s10b>;
+ w-disable1-gpios = <&tlmm 134 GPIO_ACTIVE_LOW>;
+ w-disable2-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+ uart-wake-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&wcn_wlan_bt_en>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* PCIe interface for Wi-Fi */
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlan_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&pcie4_ep>;
+ };
+ };
+
+ /* USB interface for BT */
+ port@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlan_usb_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usb_hub_m2_ep>;
+ };
+ };
+
+ /* UART interface for BT */
+ port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wlan_uart_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&uart2_ep>;
+ };
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-l1-l4-supply = <&vreg_s12b>;
+ vdd-l2-l7-supply = <&vreg_bob>;
+ vdd-l3-l5-supply = <&vreg_s11b>;
+ vdd-l6-l9-l10-supply = <&vreg_s12b>;
+ vdd-l8-supply = <&vreg_s12b>;
+
+ vreg_s10b: smps10 {
+ regulator-name = "vreg_s10b";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_s11b: smps11 {
+ regulator-name = "vreg_s11b";
+ regulator-min-microvolt = <1272000>;
+ regulator-max-microvolt = <1272000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s12b: smps12 {
+ regulator-name = "vreg_s12b";
+ regulator-min-microvolt = <984000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b: ldo1 {
+ regulator-name = "vreg_l1b";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3b: ldo3 {
+ regulator-name = "vreg_l3b";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4b: ldo4 {
+ regulator-name = "vreg_l4b";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b: ldo6 {
+ regulator-name = "vreg_l6b";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8350c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-bob-supply = <&vph_pwr>;
+ vdd-l1-l12-supply = <&vreg_s1c>;
+ vdd-l2-l8-supply = <&vreg_s1c>;
+ vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+ vdd-l6-l9-l11-supply = <&vreg_bob>;
+ vdd-l10-supply = <&vreg_s11b>;
+
+ vreg_s1c: smps1 {
+ regulator-name = "vreg_s1c";
+ regulator-min-microvolt = <1888000>;
+ regulator-max-microvolt = <1888000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13c: ldo13 {
+ regulator-name = "vreg_l13c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-name = "vreg_bob";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-always-on;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-l4-supply = <&vreg_s11b>;
+ vdd-l2-l7-supply = <&vreg_bob>;
+ vdd-l3-l5-supply = <&vreg_s11b>;
+ vdd-l6-l9-l10-supply = <&vreg_s12b>;
+ vdd-l8-supply = <&vreg_s12b>;
+
+ vreg_l2d: ldo2 {
+ regulator-name = "vreg_l2d";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3d: ldo3 {
+ regulator-name = "vreg_l3d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4d: ldo4 {
+ regulator-name = "vreg_l4d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6d: ldo6 {
+ regulator-name = "vreg_l6d";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7d: ldo7 {
+ regulator-name = "vreg_l7d";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8d: ldo8 {
+ regulator-name = "vreg_l8d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9d: ldo9 {
+ regulator-name = "vreg_l9d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10d: ldo10 {
+ regulator-name = "vreg_l10d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc0 {
+ status = "okay";
+};
+
+&gpi_dma0 {
+ dma-channel-mask = <0x3f>;
+ status = "okay";
+};
+
+&gpi_dma1 {
+ dma-channel-mask = <0x3f>;
+ status = "okay";
+};
+
+&gpi_dma2 {
+ dma-channel-mask = <0x3f>;
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ /* Reuse firmware from x13s as the SoC is unfused */
+ firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcdxkmsuc8280.mbn";
+};
+
+&i2c12 {
+ clock-frequency = <400000>;
+
+ pinctrl-0 = <&qup_i2c12_data_clk>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ eeprom@50 {
+ compatible = "belling,bl24c16f", "atmel,24c16";
+ reg = <0x50>;
+ pagesize = <16>;
+ vcc-supply = <&vreg_s10b>;
+ wp-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-address@9e {
+ reg = <0x9e 0x6>;
+ };
+
+ mac_addr1: mac-address@a4 {
+ reg = <0xa4 0x6>;
+ };
+ };
+ };
+
+ rtc@68 {
+ compatible = "st,m41t11";
+ reg = <0x68>;
+ };
+};
+
+/* QPS615 PCIe Switch */
+&i2c21 {
+ pinctrl-0 = <&qup_i2c21_data_clk>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&iris {
+ firmware-name = "qcom/vpu/vpu20_p4_gen2_s6.mbn";
+
+ status = "okay";
+};
+
+&lpass_tlmm {
+ status = "okay";
+};
+
+&mdss0 {
+ status = "okay";
+};
+
+&mdss0_dp0 {
+ status = "okay";
+};
+
+&mdss0_dp0_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&usb_0_qmpphy_dp_in>;
+};
+
+&mdss0_dp1 {
+ status = "okay";
+};
+
+&mdss0_dp1_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&usb_1_qmpphy_dp_in>;
+};
+
+&mdss0_dp2 {
+ status = "okay";
+};
+
+&mdss0_dp2_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&hdmi_bridge_dp_in>;
+};
+
+&mdss0_dp2_phy {
+ vdda-phy-supply = <&vreg_l3b>;
+ vdda-pll-supply = <&vreg_l6b>;
+
+ status = "okay";
+};
+
+/* M-key Gen3 x4 */
+&pcie2a {
+ /* Place ECAM and BAR space above 4 GiB to accommodate large BARs. */
+ reg = <0x0 0x01c20000 0x0 0x3000>,
+ <0x0 0x3c000000 0x0 0xf1d>,
+ <0x0 0x3c000f20 0x0 0xa8>,
+ <0x0 0x3c001000 0x0 0x1000>,
+ <0x5 0x00000000 0x0 0x10000000>, /* ECAM config */
+ <0x0 0x01c23000 0x0 0x1000>;
+
+ ranges = /* IO (1 MiB) */
+ <0x01000000 0x0 0x00000000 0x0 0x3c200000 0x0 0x100000>,
+ /* 32-bit non-prefetchable memory (256 MiB) */
+ <0x02000000 0x0 0x40000000 0x5 0x10000000 0x0 0x10000000>,
+ /* 64-bit non-prefetchable memory (3.5 GiB) */
+ <0x03000000 0x5 0x20000000 0x5 0x20000000 0x0 0xe0000000>;
+
+ pinctrl-0 = <&pcie2a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie2a_port0 {
+ compatible = "pciclass,0604";
+
+ reset-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+
+ port {
+ pcie2a_ep: endpoint {
+ remote-endpoint = <&nvme_pcie_ep>;
+ };
+ };
+};
+
+&pcie2a_phy {
+ vdda-phy-supply = <&vreg_l6d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+/* QPS615 */
+&pcie3a {
+ reg = <0x0 0x01c10000 0x0 0x3000>,
+ <0x0 0x34000000 0x0 0xf1d>,
+ <0x0 0x34000f20 0x0 0xa8>,
+ <0x0 0x34001000 0x0 0x1000>,
+ <0x4 0x80000000 0x0 0x10000000>, /* ECAM config */
+ <0x0 0x01c13000 0x0 0x1000>;
+
+ ranges = /* IO (1 MiB) */
+ <0x01000000 0x0 0x00000000 0x0 0x34200000 0x0 0x100000>,
+ /* 32-bit non-prefetchable memory (256 MiB) */
+ <0x02000000 0x0 0x40000000 0x4 0x90000000 0x0 0x10000000>,
+ /* 64-bit non-prefetchable memory (512 MiB) */
+ <0x03000000 0x4 0xa0000000 0x4 0xa0000000 0x0 0x20000000>;
+
+ num-lanes = <2>;
+
+ pinctrl-0 = <&pcie3a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie3a_phy {
+ vdda-phy-supply = <&vreg_l6d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&pcie3a_port0 {
+ reset-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+ pcie@0,0 {
+ compatible = "pci1179,0623";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ bus-range = <0x2 0xff>;
+
+ vddc-supply = <&vdd_ntn_core_0p9>;
+ vdd18-supply = <&vcc_1v8>;
+ vdd09-supply = <&vdd_ntn_core_0p9>;
+ vddio1-supply = <&vcc_1v8>;
+ vddio2-supply = <&vcc_1v8>;
+ vddio18-supply = <&vcc_1v8>;
+
+ i2c-parent = <&i2c21 0x77>;
+
+ resx-gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&tc9563_resx_n>;
+ pinctrl-names = "default";
+
+ /* I-PEX BTB Connector */
+ pcie@1,0 {
+ reg = <0x20800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ bus-range = <0x3 0xff>;
+
+ /* Disable by default for power saving */
+ status = "disabled";
+ };
+
+ /* FPC Connector */
+ pcie@2,0 {
+ reg = <0x21000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ bus-range = <0x4 0xff>;
+
+ status = "disabled";
+ };
+
+ pcie@3,0 {
+ reg = <0x21800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ device_type = "pci";
+ ranges;
+ bus-range = <0x5 0xff>;
+
+ ethernet@0,0 {
+ reg = <0x50000 0x0 0x0 0x0 0x0>;
+
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ ethernet@0,1 {
+ reg = <0x50100 0x0 0x0 0x0 0x0>;
+
+ nvmem-cells = <&mac_addr1>;
+ nvmem-cell-names = "mac-address";
+ };
+ };
+ };
+};
+
+/* M-key Gen3 x2 */
+&pcie3b {
+ reg = <0x0 0x01c08000 0x0 0x3000>,
+ <0x0 0x32000000 0x0 0xf1d>,
+ <0x0 0x32000f20 0x0 0xa8>,
+ <0x0 0x32001000 0x0 0x1000>,
+ <0x4 0x40000000 0x0 0x10000000>, /* ECAM config */
+ <0x0 0x01c0b000 0x0 0x1000>;
+
+ ranges = /* IO (1 MiB) */
+ <0x01000000 0x0 0x00000000 0x0 0x32200000 0x0 0x100000>,
+ /* 32-bit non-prefetchable memory (256 MiB) */
+ <0x02000000 0x0 0x40000000 0x4 0x50000000 0x0 0x10000000>,
+ /* 64-bit non-prefetchable memory (512 MiB) */
+ <0x03000000 0x4 0x60000000 0x4 0x60000000 0x0 0x20000000>;
+
+ pinctrl-0 = <&pcie3b_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie3b_port0 {
+ compatible = "pciclass,0604";
+
+ reset-gpios = <&tlmm 153 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
+
+ port {
+ pcie3b_ep: endpoint {
+ remote-endpoint = <&nvme2_pcie_ep>;
+ };
+ };
+};
+
+&pcie3b_phy {
+ vdda-phy-supply = <&vreg_l6d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+/* E-key Gen2 x1 */
+&pcie4 {
+ reg = <0x0 0x01c00000 0x0 0x3000>,
+ <0x0 0x30000000 0x0 0xf1d>,
+ <0x0 0x30000f20 0x0 0xa8>,
+ <0x0 0x30001000 0x0 0x1000>,
+ <0x4 0x00000000 0x0 0x10000000>, /* ECAM config */
+ <0x0 0x01c03000 0x0 0x1000>;
+
+ ranges = /* IO (1 MiB) */
+ <0x01000000 0x0 0x00000000 0x0 0x30200000 0x0 0x100000>,
+ /* 32-bit non-prefetchable memory (256 MiB) */
+ <0x02000000 0x0 0x40000000 0x4 0x10000000 0x0 0x10000000>,
+ /* 64-bit non-prefetchable memory (512 MiB) */
+ <0x03000000 0x4 0x20000000 0x4 0x20000000 0x0 0x20000000>;
+
+ max-link-speed = <2>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_port0 {
+ compatible = "pciclass,0604";
+
+ reset-gpios = <&tlmm 141 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 139 GPIO_ACTIVE_LOW>;
+
+ port {
+ pcie4_ep: endpoint {
+ remote-endpoint = <&wlan_pcie_ep>;
+ };
+ };
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l6d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&pmc8280c_gpios {
+ eth_phy_pwr_en: eth-phy-pwr-en-state {
+ pins = "gpio4";
+ function = "normal";
+ };
+
+ usb2_reg_en: usb2-reg-en-state {
+ pins = "gpio5";
+ function = "normal";
+ };
+
+ usb3_reg_en: usb3-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ };
+};
+
+&pmk8280_adc_tm {
+ status = "okay";
+
+ sys-therm@0 {
+ reg = <0>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@1 {
+ reg = <1>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@2 {
+ reg = <2>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@3 {
+ reg = <3>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@4 {
+ reg = <4>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@5 {
+ reg = <5>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@6 {
+ reg = <6>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@7 {
+ reg = <7>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+};
+
+&pmk8280_pon_pwrkey {
+ status = "okay";
+};
+
+&pmk8280_vadc {
+ channel@108 {
+ reg = <PM8350_ADC7_AMUX_THM5(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "adp12v_det";
+ };
+
+ channel@144 {
+ reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm1";
+ };
+
+ channel@145 {
+ reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm2";
+ };
+
+ channel@146 {
+ reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm3";
+ };
+
+ channel@147 {
+ reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm4";
+ };
+
+ channel@344 {
+ reg = <PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm5";
+ };
+
+ channel@345 {
+ reg = <PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm6";
+ };
+
+ channel@346 {
+ reg = <PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm7";
+ };
+
+ channel@347 {
+ reg = <PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm8";
+ };
+};
+
+&pmr735a_gpios {
+ hastings_reg_en: hastings-reg-en-state {
+ pins = "gpio1";
+ function = "normal";
+ };
+};
+
+&qup0 {
+ firmware-name = "qcom/sc8280xp/qupv3fw.elf";
+ status = "okay";
+};
+
+&qup1 {
+ firmware-name = "qcom/sc8280xp/qupv3fw.elf";
+ status = "okay";
+};
+
+&qup2 {
+ firmware-name = "qcom/sc8280xp/qupv3fw.elf";
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sc8280xp/radxa/dragon-q8b/qcadsp8280.mbn";
+ status = "okay";
+};
+
+&remoteproc_nsp0 {
+ firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";
+ status = "okay";
+};
+
+&rxmacro {
+ status = "okay";
+};
+
+&sdc2 {
+ pinctrl-0 = <&sdc2_default_state>;
+ pinctrl-1 = <&sdc2_sleep_state>;
+ pinctrl-names = "default", "sleep";
+
+ full-pwr-cycle;
+
+ vmmc-supply = <&vreg_l9c>;
+ vqmmc-supply = <&vreg_l6c>;
+
+ cd-gpios = <&tlmm 131 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+};
+
+&sound {
+ compatible = "qcom,sc8280xp-sndcard";
+ model = "SC8280XP-Radxa-Dragon-Q8B";
+
+ audio-routing =
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "TX SWR_ADC1", "ADC2_OUTPUT";
+
+ dp0-dai-link {
+ link-name = "DP0 Playback";
+
+ codec {
+ sound-dai = <&mdss0_dp0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai DISPLAY_PORT_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ dp1-dai-link {
+ link-name = "DP1 Playback";
+
+ codec {
+ sound-dai = <&mdss0_dp1>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai DISPLAY_PORT_RX_1>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ dp2-dai-link {
+ link-name = "DP2 Playback";
+
+ codec {
+ sound-dai = <&mdss0_dp2>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai DISPLAY_PORT_RX_2>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ wcd_rx: wcd9380-rx@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ wcd_tx: wcd9380-tx@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <1 1 2 3>;
+ };
+};
+
+&txmacro {
+ status = "okay";
+};
+
+/* E-key Bluetooth */
+&uart2 {
+ uart-has-rtscts;
+ status = "okay";
+
+ port {
+ uart2_ep: endpoint {
+ remote-endpoint = <&wlan_uart_ep>;
+ };
+ };
+};
+
+&uart17 {
+ compatible = "qcom,geni-debug-uart";
+
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vcc_ufs>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l3d>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l6b>;
+ vdda-pll-supply = <&vreg_l3b>;
+
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_con0_hs>;
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l9d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l9d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ mode-switch;
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy_dp_in {
+ remote-endpoint = <&mdss0_dp0_out>;
+};
+
+&usb_0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con0_ss>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_con1_hs>;
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l4b>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l13c>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l4b>;
+ vdda-pll-supply = <&vreg_l3b>;
+
+ mode-switch;
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy_dp_in {
+ remote-endpoint = <&mdss0_dp1_out>;
+};
+
+&usb_1_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con1_ss>;
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_hub_m2: hub@3 {
+ compatible = "usb1a86,8091";
+ reg = <3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@2 {
+ reg = <2>;
+
+ usb_hub_m2_ep: endpoint {
+ remote-endpoint = <&wlan_usb_ep>;
+ };
+ };
+ };
+ };
+};
+
+&usb_2_hsphy0 {
+ vdda-pll-supply = <&vreg_l1b>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy1 {
+ vdda-pll-supply = <&vreg_l8d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy2 {
+ vdda-pll-supply = <&vreg_l10d>;
+ vdda18-supply = <&vreg_l8c>;
+ vdda33-supply = <&vreg_l2d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy3 {
+ vdda-pll-supply = <&vreg_l10d>;
+ vdda18-supply = <&vreg_l8c>;
+ vdda33-supply = <&vreg_l2d>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy0 {
+ vdda-phy-supply = <&vreg_l1b>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy1 {
+ vdda-phy-supply = <&vreg_l8d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&vamacro {
+ vdd-micb-supply = <&vreg_s10b>;
+
+ qcom,dmic-sample-rate = <4800000>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */
+
+&qup_i2c12_data_clk {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_i2c21_data_clk {
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <74 6>, /* QSPI Flash */
+ <125 5>; /* SPI (TPM) */
+ gpio-line-names =
+ /* GPIO_0 ~ GPIO_3 */
+ "", "", "", "",
+ /* GPIO_4 ~ GPIO_7 */
+ "", "", "", "",
+ /* GPIO_8 ~ GPIO_11 */
+ "", "", "", "",
+ /* GPIO_12 ~ GPIO_15 */
+ "", "", "", "",
+ /* GPIO_16 ~ GPIO_19 */
+ "", "", "", "",
+ /* GPIO_20 ~ GPIO_23 */
+ "", "", "", "",
+ /* GPIO_24 ~ GPIO_27 */
+ "", "", "", "",
+ /* GPIO_28 ~ GPIO_31 */
+ "", "", "", "",
+ /* GPIO_32 ~ GPIO_35 */
+ "", "", "", "",
+ /* GPIO_36 ~ GPIO_39 */
+ "", "", "", "",
+ /* GPIO_40 ~ GPIO_43 */
+ "", "PIN_3", "PIN_5", "PIN_27",
+ /* GPIO_44 ~ GPIO_47 */
+ "PIN_28", "", "", "",
+ /* GPIO_48 ~ GPIO_51 */
+ "", "", "", "",
+ /* GPIO_52 ~ GPIO_55 */
+ "", "", "", "",
+ /* GPIO_56 ~ GPIO_59 */
+ "", "", "", "",
+ /* GPIO_60 ~ GPIO_63 */
+ "", "", "", "PIN_8",
+ /* GPIO_64 ~ GPIO_67 */
+ "PIN_10", "", "PIN_13", "PIN_15",
+ /* GPIO_68 ~ GPIO_71 */
+ "PIN_16", "PIN_37", "", "",
+ /* GPIO_72 ~ GPIO_75 */
+ "", "", "", "",
+ /* GPIO_76 ~ GPIO_79 */
+ "", "", "", "",
+ /* GPIO_80 ~ GPIO_83 */
+ "", "", "", "",
+ /* GPIO_84 ~ GPIO_87 */
+ "", "", "", "PIN_21",
+ /* GPIO_88 ~ GPIO_91 */
+ "PIN_19", "PIN_23", "PIN_24", "PIN_26",
+ /* GPIO_92 ~ GPIO_95 */
+ "PIN_22", "", "", "",
+ /* GPIO_96 ~ GPIO_99 */
+ "", "", "", "",
+ /* GPIO_100 ~ GPIO_103 */
+ "", "", "", "",
+ /* GPIO_104 ~ GPIO_107 */
+ "", "", "", "",
+ /* GPIO_108 ~ GPIO_111 */
+ "", "", "PIN_18", "PIN_11",
+ /* GPIO_112 ~ GPIO_115 */
+ "PIN_36", "", "PIN_32", "PIN_33",
+ /* GPIO_116 ~ GPIO_119 */
+ "", "", "", "",
+ /* GPIO_120 ~ GPIO_123 */
+ "", "", "", "",
+ /* GPIO_124 ~ GPIO_127 */
+ "", "", "", "",
+ /* GPIO_128 ~ GPIO_131 */
+ "", "", "", "",
+ /* GPIO_132 ~ GPIO_135 */
+ "", "", "", "",
+ /* GPIO_136 ~ GPIO_139 */
+ "", "", "", "",
+ /* GPIO_140 ~ GPIO_143 */
+ "", "", "", "",
+ /* GPIO_144 ~ GPIO_147 */
+ "", "", "", "",
+ /* GPIO_148 ~ GPIO_151 */
+ "", "", "", "",
+ /* GPIO_152 ~ GPIO_155 */
+ "", "", "", "",
+ /* GPIO_156 ~ GPIO_159 */
+ "PIN_31", "PIN_29", "", "",
+ /* GPIO_160 ~ GPIO_163 */
+ "", "", "", "",
+ /* GPIO_164 ~ GPIO_167 */
+ "", "", "", "",
+ /* GPIO_168 ~ GPIO_171 */
+ "", "", "", "PIN_35",
+ /* GPIO_172 ~ GPIO_175 */
+ "PIN_38", "PIN_40", "PIN_12", "PIN_7",
+ /* GPIO_176 ~ GPIO_179 */
+ "", "", "", "";
+
+ dp_hpd_default: dp-hpd-default-state {
+ pins = "gpio2";
+ function = "edp_hot";
+ bias-disable;
+ };
+
+ ntn_0p9_en: ntn-0p9-en-state {
+ pins = "gpio160";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio135";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ nvme2_reg_en: nvme2-reg-en-state {
+ pins = "gpio158";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pcie2a_default: pcie2a-default-state {
+ clkreq-n-pins {
+ pins = "gpio142";
+ function = "pcie2a_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio143";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio145";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie3a_default: pcie3a-default-state {
+ clkreq-n-pins {
+ pins = "gpio150";
+ function = "pcie3a_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio151";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie3b_default: pcie3b-default-state {
+ clkreq-n-pins {
+ pins = "gpio152";
+ function = "pcie3b_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio153";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wake-n-pins {
+ pins = "gpio149";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio140";
+ function = "pcie4_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio141";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio139";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_default_state: sdc2-default-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ card-detect-pins {
+ pins = "gpio131";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ sdc2_sleep_state: sdc2-sleep-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ card-detect-pins {
+ pins = "gpio131";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ tc9563_resx_n: tc9563-resx-state {
+ pins = "gpio108";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb0_sbu_default: usb0-sbu-state {
+ oe-n-pins {
+ pins = "gpio101";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio164";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ usb1_sbu_default: usb1-sbu-state {
+ oe-n-pins {
+ pins = "gpio48";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio47";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ vcc_1v8_reg_en: vcc-1v8-reg-en-state {
+ pins = "gpio161";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ vcc_5v_s_reg_en: vcc-5v-s-reg-en-state {
+ pins = "gpio159";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcd_default: wcd-default-state {
+ reset-pins {
+ pins = "gpio106";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ wcn_wlan_bt_en: wcn-wlan-en-state {
+ pins = "gpio133", "gpio134";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ user_led: user-led-state {
+ pins = "gpio4";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
--
2.55.0