Re: [PATCH] media: i2c: ov5645: Fix CSI-2 CRC errors on RK3576 after init sequence

[Laurent Pinchart]

On Tue, Sep 08, 2026 at 01:14:32PM +0300, Sakari Ailus wrote:
> On Wed, Aug 26, 2026 at 08:54:32AM +0000, Xiaolei Wang wrote:
> > On the RK3576 platform, after ov5645_global_init_setting completes and
> > before stream on, the CSI host reports a high rate of CRC errors:
> > 
> >   MIPI_CSI2 ERR1:0x1000000 (crc,vc: 0)
> > 
> > These errors occur exclusively in the window between init completion and
> > stream on. Once preview starts and the sensor outputs valid HS data, no
> > further CRC errors are observed.
> > 
> > Commit 092e8eb90a7d ("media: i2c: ov5645: Fix power sequence") reworked
> > the power sequence to properly enter LP-11 during power-up. As part of
> > this change, the SYSTEM_CTRL0_STOP (0x42) write in s_power() was replaced
> > with usleep_range(500, 1000), leaving the sensor in wake state (0x3008 =
> > 0x02) from init through to s_stream. Reverting this commit resolves the
> > CRC errors, confirming it as the triggering change.
> > 
> > Restore the power-down state after init by appending { 0x3008, 0x42 } to
> > the end of ov5645_global_init_setting[]. This powers down the sensor core
> > after MIPI configuration is complete, while keeping the MIPI PHY active in
> > LP-11. The sensor is then woken up only at s_stream time.
> > 
> > This preserves all LP-11 compliance improvements from
> > commit 092e8eb90a7d ("media: i2c: ov5645: Fix power sequence") while
> > eliminating the CRC errors on RK3576.
> > 
> > Fixes: 092e8eb90a7d ("media: i2c: ov5645: Fix power sequence")
> > Signed-off-by: Xiaolei Wang <xiaoleiwangxiaolei@xxxxxxxxx>
> > ---
> >  drivers/media/i2c/ov5645.c | 3 ++-
> >  1 file changed, 2 insertions(+), 1 deletion(-)
> > 
> > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c
> > index c772ef6e51d2..be85e0155b81 100644
> > --- a/drivers/media/i2c/ov5645.c
> > +++ b/drivers/media/i2c/ov5645.c
> > @@ -351,7 +351,8 @@ static const struct reg_value ov5645_global_init_setting[] = {
> >  	{ 0x3008, 0x02 },
> >  	{ OV5645_IO_MIPI_CTRL00, 0x40 },
> >  	{ OV5645_MIPI_CTRL00, 0x24 },
> > -	{ OV5645_PAD_OUTPUT00, 0x70 }
> > +	{ OV5645_PAD_OUTPUT00, 0x70 },
> > +	{ 0x3008, 0x42 }

While at it, please use the register macro.

> Is the earlier write of 0x3008 still appropriate?

There are four earlier writes of register 0x3008. The whole
initialization sequence likely needs a cleanup. It's not clear why
software suspend needs to be disabled briefly during initialization.

> >  };
> >  
> >  static const struct reg_value ov5645_setting_sxga[] = {

-- 
Regards,

Laurent Pinchart