[PATCH v3 3/3] arm64: dts: qcom: hamoa-iot-evk: switch typec0 to PS8830 retimer
From: Xin Liu
Date: Mon Sep 14 2026 - 06:29:01 EST
The Hamoa IoT EVK hardware design uses a Parade PS8830 retimer on
I2C3 for USB Type-C port 0. Describe the retimer and route typec0
through it to enable USB 3.0 SuperSpeed and DisplayPort Alt Mode.
Supply the PS8830 from the existing vreg_rtmr0_* rails and remove
their stale "Left unused" annotation.
The FSUSB42 SBU mux chip is present on the PCB but with all signal
lines unconnected (NC), so remove the fsusb42 node and its pinctrl
group. The chip is retained as a hardware fallback: should the PS8830's
SBU path encounter issues, the FSUSB42 can be activated with a simple
rework, avoiding a full board respin.
Co-developed-by: Guodong Xu <guodong.xu@xxxxxxxxxxxxxxxx>
Signed-off-by: Guodong Xu <guodong.xu@xxxxxxxxxxxxxxxx>
Signed-off-by: Xin Liu <xin.liu@xxxxxxxxxxxxxxxx>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxxxxxxxx>
---
v3: Replace RPMH_RF_CLK4 reference with a fixed-clock node; split off
clock fix into a separate patch (2/3).
v2: Updated the commit message to clarify that FSUSB42 is present on
PCB but with all signal lines unconnected (NC).
---
arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 114 ++++++++++++---------
1 file changed, 66 insertions(+), 48 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 57c8ae2e7d4c..a4a2a1fccf11 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -36,6 +36,12 @@ mcp2518fd_osc: clock-40000000 {
#clock-cells = <0>;
};
+ clk_rtmr0_xo: clock-rtmr0-xo {
+ compatible = "fixed-clock";
+ clock-frequency = <25000000>;
+ #clock-cells = <0>;
+ };
+
clk_rtmr1_xo: clock-rtmr1-xo {
compatible = "fixed-clock";
clock-frequency = <25000000>;
@@ -138,15 +144,15 @@ port@1 {
reg = <1>;
pmic_glink_ss0_ss_in: endpoint {
- remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ remote-endpoint = <&retimer_ss0_ss_out>;
};
};
port@2 {
reg = <2>;
- pmic_glink_ss0_sbu: endpoint {
- remote-endpoint = <&usb_1_ss0_sbu_mux>;
+ pmic_glink_ss0_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss0_con_sbu_out>;
};
};
};
@@ -315,7 +321,6 @@ vreg_pcie_3v3_aux: regulator-pcie-3v3-aux {
pinctrl-names = "default";
};
- /* Left unused as the retimer is not used on this board. */
vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
compatible = "regulator-fixed";
@@ -644,25 +649,6 @@ platform {
};
};
- usb-1-ss0-sbu-mux {
- compatible = "onnn,fsusb42", "gpio-sbu-mux";
-
- enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
- select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
-
- pinctrl-0 = <&usb_1_ss0_sbu_default>;
- pinctrl-names = "default";
-
- mode-switch;
- orientation-switch;
-
- port {
- usb_1_ss0_sbu_mux: endpoint {
- remote-endpoint = <&pmic_glink_ss0_sbu>;
- };
- };
- };
-
wifi-bt-connector {
compatible = "pcie-m2-e-connector";
vpcie3v3-supply = <&vreg_wcn_3p3>;
@@ -759,6 +745,62 @@ retimer_ss2_con_sbu_out: endpoint {
};
};
+&i2c3 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ typec-mux@8 {
+ compatible = "parade,ps8830";
+ reg = <0x08>;
+
+ clocks = <&clk_rtmr0_xo>;
+
+ vdd-supply = <&vreg_rtmr0_1p15>;
+ vdd33-supply = <&vreg_rtmr0_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+ vddar-supply = <&vreg_rtmr0_1p15>;
+ vddat-supply = <&vreg_rtmr0_1p15>;
+ vddio-supply = <&vreg_rtmr0_1p8>;
+
+ reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&rtmr0_default>;
+ pinctrl-names = "default";
+
+ orientation-switch;
+ retimer-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss0_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss0_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss0_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+ };
+ };
+ };
+ };
+};
+
&i2c5 {
clock-frequency = <400000>;
@@ -1413,30 +1455,6 @@ usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state {
bias-disable;
};
- usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
- mode-pins {
- pins = "gpio166";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- output-high;
- };
-
- oe-n-pins {
- pins = "gpio168";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- };
-
- sel-pins {
- pins = "gpio167";
- function = "gpio";
- bias-disable;
- drive-strength = <2>;
- };
- };
-
wcd_default: wcd-reset-n-active-state {
pins = "gpio191";
function = "gpio";
@@ -1524,7 +1542,7 @@ &usb_1_ss0_hsphy {
};
&usb_1_ss0_qmpphy_out {
- remote-endpoint = <&pmic_glink_ss0_ss_in>;
+ remote-endpoint = <&retimer_ss0_ss_in>;
};
&usb_1_ss1_dwc3_hs {
--
2.43.0