Re: [PATCH v11 1/3] dt-bindings: phy: Add documentation for Airoha AN7581 USB PHY

[Manivannan Sadhasivam]

On Fri, Jul 24, 2026 at 08:45:20PM +0200, Christian Marangi wrote:
> Add documentation for Airoha AN7581 USB PHY that describe the USB PHY
> for the USB controller.
> 
> Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> always supported. The USB 3.0 mode is optional and depends on the Serdes
> mode currently configured on the system for the relevant USB port.
> 
> To correctly calibrate, the USB 2.0 port require correct value in
> "airoha,usb2-monitor-clk-sel" property. Both the 2 USB 2.0 port permit
> selecting one of the 4 monitor clock for calibration (internal clock not
> exposed to the system) but each port have only one of the 4 actually
> connected in HW hence the correct value needs to be specified in DT
> based on board and the physical port. Normally it's monitor clock 1 for
> USB1 and monitor clock 2 for USB2.
> 
> To correctly setup the Serdes mode attached to the USB 3.0 mode, a phys
> property is required with the phandle pointing to the correct Serdes port
> provided by the SCU node. Providing the phys property is optional if USB
> 3.0 is not used.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@xxxxxxxxx>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxxxxx>
> ---
>  .../bindings/phy/airoha,an7581-usb-phy.yaml   | 62 +++++++++++++++++++
>  MAINTAINERS                                   |  6 ++
>  2 files changed, 68 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> new file mode 100644
> index 000000000000..f42e3d49a61f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> @@ -0,0 +1,62 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/airoha,an7581-usb-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Airoha AN7581 SoC USB PHY
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@xxxxxxxxx>
> +
> +description: >
> +  The Airoha AN7581 SoC USB PHY describes the USB PHY for the USB controller.
> +
> +  Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> +  always supported. The USB 3.0 mode is optional and depends on the Serdes
> +  mode currently configured on the system for the relevant USB port.
> +
> +properties:
> +  compatible:
> +    const: airoha,an7581-usb-phy
> +
> +  reg:
> +    maxItems: 1
> +
> +  airoha,usb2-monitor-clk-sel:
> +    description: Describe what oscillator across the available 4
> +      should be selected for USB 2.0 Slew Rate calibration.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2, 3]
> +
> +  phys:
> +    items:
> +      - description: phandle to Serdes PHY. Optional if USB 3.0 is not used.
> +
> +  '#phy-cells':
> +    description: The cell contains the mode, PHY_TYPE_USB2 or PHY_TYPE_USB3,
> +      as defined in dt-bindings/phy/phy.h.
> +    const: 1
> +
> +required:
> +  - compatible
> +  - reg
> +  - airoha,usb2-monitor-clk-sel
> +  - '#phy-cells'
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/soc/airoha,scu-ssr.h>

Rob's bot triggered compilation error due to this missing header.

- Mani

-- 
மணிவண்ணன் சதாசிவம்