[PATCH 12/17] ARM: dts: samsung: exynos4210-trats: sort properties
From: Henrik Grimler
Date: Sun Oct 04 2026 - 16:20:26 EST
And add or delete newlines where applicable, and sort properties
according to the preferred style. Fixes warnings from dt-check-style
like:
samsung/exynos4210-trats.dts:122: [property-order] property 'label' out of canonical order (should sort before 'linux,code')
samsung/exynos4210-trats.dts:179: [required-blank-lines] "status" must be preceded by a blank line
samsung/exynos4210-trats.dts:183: [property-order] property 'compatible' out of canonical order (should sort before 'reg')
Signed-off-by: Henrik Grimler <henrik.grimler@xxxxxxxx>
---
arch/arm/boot/dts/samsung/exynos4210-trats.dts | 60 ++++++++++++++++----------
1 file changed, 38 insertions(+), 22 deletions(-)
diff --git a/arch/arm/boot/dts/samsung/exynos4210-trats.dts b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
index 20fe148387fc..8d4ebcf86775 100644
--- a/arch/arm/boot/dts/samsung/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/samsung/exynos4210-trats.dts
@@ -96,31 +96,31 @@ gpio-keys {
vol-down-key {
gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
- linux,code = <114>;
label = "volume down";
debounce-interval = <10>;
+ linux,code = <114>;
};
vol-up-key {
gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
- linux,code = <115>;
label = "volume up";
debounce-interval = <10>;
+ linux,code = <115>;
};
power-key {
gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
- linux,code = <116>;
label = "power";
debounce-interval = <10>;
wakeup-source;
+ linux,code = <116>;
};
ok-key {
gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
- linux,code = <352>;
label = "ok";
debounce-interval = <10>;
+ linux,code = <352>;
};
};
@@ -163,6 +163,7 @@ map0 {
/* Corresponds to 800MHz at freq_table */
cooling-device = <&cpu0 2 2>, <&cpu1 2 2>;
};
+
map1 {
/* Corresponds to 200MHz at freq_table */
cooling-device = <&cpu0 4 4>, <&cpu1 4 4>;
@@ -176,11 +177,12 @@ &dsi_0 {
samsung,burst-clock-frequency = <500000000>;
samsung,esc-clock-frequency = <20000000>;
samsung,pll-clock-frequency = <24000000>;
+
status = "okay";
panel@0 {
- reg = <0>;
compatible = "samsung,s6e8aa0";
+ reg = <0>;
vdd3-supply = <&vcclcd_reg>;
vci-supply = <&vlcd_reg>;
reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
@@ -209,40 +211,45 @@ timing-0 {
};
&exynos_usbphy {
- status = "okay";
vbus-supply = <&safe1_sreg>;
+
+ status = "okay";
};
&fimc_0 {
- status = "okay";
assigned-clocks = <&clock CLK_MOUT_FIMC0>,
<&clock CLK_SCLK_FIMC0>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimc_1 {
- status = "okay";
assigned-clocks = <&clock CLK_MOUT_FIMC1>,
<&clock CLK_SCLK_FIMC1>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimc_2 {
- status = "okay";
assigned-clocks = <&clock CLK_MOUT_FIMC2>,
<&clock CLK_SCLK_FIMC2>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
- assigned-clock-rates = <0>, <160000000>;
+ assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimc_3 {
- status = "okay";
assigned-clocks = <&clock CLK_MOUT_FIMC3>,
<&clock CLK_SCLK_FIMC3>;
assigned-clock-parents = <&clock CLK_SCLK_MPLL>;
assigned-clock-rates = <0>, <160000000>;
+
+ status = "okay";
};
&fimd {
@@ -257,15 +264,18 @@ &hsotg {
vusb_d-supply = <&vusb_reg>;
vusb_a-supply = <&vusbdac_reg>;
dr_mode = "peripheral";
+
status = "okay";
};
&i2c_3 {
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <400000>;
- pinctrl-0 = <&i2c3_bus>;
- pinctrl-names = "default";
+
status = "okay";
touchscreen@48 {
@@ -281,11 +291,13 @@ touchscreen@48 {
};
&i2c_5 {
+ pinctrl-0 = <&i2c5_bus>;
+ pinctrl-names = "default";
+
samsung,i2c-sda-delay = <100>;
samsung,i2c-slave-addr = <0x10>;
samsung,i2c-max-bus-freq = <100000>;
- pinctrl-0 = <&i2c5_bus>;
- pinctrl-names = "default";
+
status = "okay";
pmic@66 {
@@ -312,9 +324,9 @@ pmic@66 {
<1000000>, <950000>;
max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>,
- <950000>, <900000>,
+ <950000>, <900000>,
<1100000>, <1000000>,
- <950000>, <900000>;
+ <950000>, <900000>;
max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
@@ -488,9 +500,10 @@ bt_device_wakeup: bt-device-wakeup-pins {
};
&rtc {
- status = "okay";
clocks = <&clock CLK_RTC>, <&pmic_ap_clk>;
clock-names = "rtc", "rtc_src";
+
+ status = "okay";
};
&sdhci_0 {
@@ -499,6 +512,7 @@ &sdhci_0 {
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
pinctrl-names = "default";
vmmc-supply = <&vemmc_reg>;
+
status = "okay";
};
@@ -508,12 +522,11 @@ &sdhci_2 {
pinctrl-names = "default";
vmmc-supply = <&tflash_reg>;
cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+
status = "okay";
};
&sdhci_3 {
- status = "okay";
-
#address-cells = <1>;
#size-cells = <0>;
@@ -523,8 +536,10 @@ &sdhci_3 {
mmc-pwrseq = <&wlan_pwrseq>;
vmmc-supply = <&tflash_reg>;
- pinctrl-names = "default";
pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
+ pinctrl-names = "default";
+
+ status = "okay";
brcmf: wifi@1 {
compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
@@ -537,12 +552,13 @@ brcmf: wifi@1 {
};
&serial_0 {
- status = "okay";
pinctrl-0 = <&uart0_data &uart0_fctl>;
pinctrl-names = "default";
uart-has-rtscts;
+ status = "okay";
+
bluetooth {
compatible = "brcm,bcm4330-bt";
--
2.43.0