Re: [PATCH v2 2/3] mfd: aat2870: Convert to use OF bindings

[Daniel Thompson]

On Mon, Oct 05, 2026 at 08:18:31PM +0300, Svyatoslav Ryhel wrote:
> пн, 5 жовт. 2026 р. о 19:51 Daniel Thompson <danielt@xxxxxxxxxx> пише:
> >
> > On Sun, Oct 04, 2026 at 07:41:20PM +0300, Svyatoslav Ryhel wrote:
> > > Conversion of the AAT2870 driver to use OF bindings requires a few complex
> > > changes that should be done simultaneously.
> > >
> > > The AAT2870 essentially provides two functions via child devices:
> > > backlight and regulators. Both functions are fairly self-sufficient and
> > > may not be populated on the final board. Consequently, the MFD
> > > registration API was replaced with of_platform_populate(), and each
> > > sub-device was given its own compatible string.
> > >
> > > Additionally, aat2870-core utilizes an enable GPIO. Obtaining this GPIO
> > > was converted to use modern gpiod/OF helpers, allowing the redundant
> > > aat2870_enable() and aat2870_disable() helpers to be removed.
> > >
> > > The aat2870-regulator driver was updated to register each of the four LDOs
> > > from a dedicated OF node.
> > >
> > > The aat2870-backlight driver was changed to populate all required
> > > properties from a dedicated Device Tree node. Its channel map was updated
> > > to use u8 instead of int. Furthermore, because the maximum current is now
> > > parsed as an absolute value rather than an enum entry, the calculation and
> > > application of the maximum current were updated accordingly.
> > >
> > > All of the changes above allow platform data to be removed entirely.
> > >
> > > Signed-off-by: Svyatoslav Ryhel <clamor95@xxxxxxxxx>
> > > ---
> > >  drivers/mfd/aat2870-core.c            | 115 ++++++--------------------
> > >  drivers/regulator/aat2870-regulator.c |  76 ++++++++++++-----
> > >  drivers/video/backlight/aat2870_bl.c  |  55 ++++++------
> > >  include/linux/mfd/aat2870.h           |  95 +--------------------
> > >  4 files changed, 111 insertions(+), 230 deletions(-)
> > >
> > > [snip]
> > >
> > > diff --git a/drivers/video/backlight/aat2870_bl.c b/drivers/video/backlight/aat2870_bl.c
> > > index 8b790df1e842b..933a8f728f66a 100644
> > > --- a/drivers/video/backlight/aat2870_bl.c
> > > +++ b/drivers/video/backlight/aat2870_bl.c
> > > @@ -15,11 +15,19 @@
> > >  #include <linux/backlight.h>
> > >  #include <linux/mfd/aat2870.h>
> > >
> > > +/* Backlight has 8 channels, each bit represents one channel */
> > > +#define AAT2870_BL_CH_ALL    0xff
> > > +
> > > +/* Backlight current magnitude (uA), 450uA current is eq to 0 */
> > > +#define AAT2870_CURRENT_MIN  450
> > > +#define AAT2870_CURRENT_MAX  27900
> > > +#define AAT2870_CURRENT_STEP 900
> > > +
> > >  struct aat2870_bl_driver_data {
> > >       struct platform_device *pdev;
> > >       struct backlight_device *bd;
> > >
> > > -     int channels;
> > > +     u8 channels;
> > >       int max_current;
> > >       int brightness; /* current brightness */
> > >  };
> > > @@ -30,7 +38,7 @@ static inline int aat2870_brightness(struct aat2870_bl_driver_data *aat2870_bl,
> > >       struct backlight_device *bd = aat2870_bl->bd;
> > >       int val;
> > >
> > > -     val = brightness * (aat2870_bl->max_current - 1);
> > > +     val = brightness * aat2870_bl->max_current;
> > >       val /= bd->props.max_brightness;
> >
> > What is the purpose of max_brightness?
> >
> > Normally it is used to limit brightness but max_current is already doing
> > that. Is it just being used to reduce the number of steps in the
> > brightness scale (and if so, why is that useful)?
> >
>
> This is the original driver behavior; I did not modify it.

I can see that but the parameters for these (rather dubious) previous
behaviours are now being copied into the devicetree bindings where they
become stable ABI.


> The AAT2870 backlight intensity is regulated by the Main Backlight
> Current Magnitude register. It has 31 steps from 450uA (0) to 27.9mA
> (31), so even setting max_current to 0 will not disable the backlight.
> The max current value may be limited for some configurations, which is
> why this property exists.
>
> The max_brightness property determines the maximum number of steps the
> backlight can have and is mapped to the available current range
> provided by the hardware. The backlight is controlled in steps, not in
> uA.

This behaviour does not match the devicetree bindings documentation for
max-brightness:

  Normally the maximum brightness is determined by the hardware and this
  property is not required. This property is used to put a software limit
  on the brightness apart from what the driver says, as it could happen
  that a LED can be made so bright that it gets damaged or causes damage
  due to restrictions in a specific system, such as mounting conditions.

Hence the question, why is the current behaviour useful?

If I understand your summary correctly the hardware has 32 steps
including 0) and the effect of max_current is to ban all brightness
values greater than max_current / AAT2870_CURRENT_STEP.

If that is the case then max_brightness if fundamentally broken because
it's default value offers more steps than exists in the hardware.
bd->props.max_brightness should be set to max_current /
AAT2870_CURRENT_STEP and the whole of aat2870_brightness() should be
removed (use backlight_get_brightness() instead).

IMHO the patchset will be cleaner if the weird max_brightness logic is
removed in a separate before doing the DT changes.


Daniel.