[PATCH 1/7] arm64: dts: qcom: shikra-cqm-evk, shikra-cqs-evk: Add HDMI overlay

[vishnu . saini]

From: Mohit Dsor <mohit.dsor@xxxxxxxxxxxxxxxx>

Add a DT overlay for CQM and CQS, to enable HDMI output when LT9611UXD
DSI-to-HDMI daughter card connected to PDISP1 DSI0 on carrier card.
LT9611UXD is connected through I2C4, with reset and interrupt connected
to tlmm GPIO76 and GPIO85.

Disable the default DSI0 panel dt nodes and enable LT9611UXD
bridge for HDMI output.

Signed-off-by: Mohit Dsor <mohit.dsor@xxxxxxxxxxxxxxxx>
Signed-off-by: Vishnu Saini <vishnu.saini@xxxxxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/qcom/Makefile                  |  6 ++
 .../boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso     | 90 ++++++++++++++++++++++
 2 files changed, 96 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4e714251d5e6..c8907e77c893 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -377,6 +377,12 @@ shikra-iqs-evk-imx577-camera-dtbs	:= shikra-iqs-evk.dtb shikra-iqs-evk-imx577-ca
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-imx577-camera.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-imx577-camera.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= shikra-iqs-evk-imx577-camera.dtb
+
+shikra-cqm-evk-hdmi-dtbs	:= shikra-cqm-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
+shikra-cqs-evk-hdmi-dtbs	:= shikra-cqs-evk.dtb shikra-cqm-cqs-evk-hdmi.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqm-evk-hdmi.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= shikra-cqs-evk-hdmi.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4250-oneplus-billie2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
diff --git a/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso b/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso
new file mode 100644
index 000000000000..a7b77114061a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/shikra-cqm-cqs-evk-hdmi.dtso
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	model = "Qualcomm Technologies, Inc. Shikra CQM/S EVK HDMI";
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_out: endpoint {
+				remote-endpoint = <&hdmi_bridge_out>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	hdmi-bridge@41 {
+		compatible = "lontium,lt9611uxd";
+		reg = <0x41>;
+		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 76 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&lcd_bias>;
+		vdd-supply = <&pm4125_l15>;
+		pinctrl-0 = <&bridge_irq_pin &bridge_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_in: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				hdmi_bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dsi0 {
+	panel@0 {
+		status = "disabled";
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&hdmi_bridge_in>;
+};
+
+&tlmm {
+	bridge_rst_pin: bridge-rst-state {
+		pins = "gpio76";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bridge_irq_pin: bridge-irq-state {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};

-- 
2.34.1