[PATCH v3 0/5] arm64: dts: qcom: kaanapali: Enable DisplayPort

[Balaji Kalkonda]

This series adds DisplayPort support for the Qualcomm Kaanapali SoC
and enables it on the MTP board.

Kaanapali has a single DisplayPort controller based on the SM8750
generation DP block, routed through the combo USB/DP QMP PHY. The
series:

 - Documents the new "qcom,kaanapali-dp" compatible in the DP controller
   and Kaanapali MDSS bindings.
 - Adds the Kaanapali descriptor to the DP driver.
 - Describes the DisplayPort controller node in kaanapali.dtsi, including
   its OPP table, clocks, and power domain, and wires it to the DPU and
   the USB/DP QMP PHY.
 - Enables USB-C audio support on the MTP board (WCD939x USBSS Type-C mux)
   as a prerequisite for exercising DP alt mode over the same Type-C port.
 - Enables the DisplayPort controller on MTP and advertises the supported
   link frequencies for DisplayPort over USB-C.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@xxxxxxxxxxxxxxxx>
---
Changes in v3:
- Merged the Kaanapali DP resource-count constraints into the existing
  2-stream MST conditional block in the DP controller binding instead of
  duplicating it (Sashiko AI).
- Added the missing additionalProperties on the displayport-controller
  pattern property in the Kaanapali MDSS binding (Sashiko AI).
- Fixed the Kaanapali DP node register block sizes to match the actual
  register ranges (Konrad).
- Removed a stray blank line between the DP node clocks and clock-names
  properties (Konrad).
- Reordered the MTP DP node overrides to keep &mdss_dp0 and
  &mdss_dp0_out alphabetically sorted among the other node references
  (Konrad).
- Link to v2: https://patch.msgid.link/20261015-kaanapali_dp-v2-0-c15cb83d9140@xxxxxxxxxxxxxxxx

Changes in v2:
- Updated the DP controller binding patch subject from "Add Kaanapali" to
  "Document Kaanapali" and rewrote its commit message to describe the
  standalone compatible and SoC-specific resource counts (Sashiko AI).
- Updated the Kaanapali DP node to use the MMCX power domain (Dmitry,
  Sashiko AI).
- Added the missing second DP stream support in the Kaanapali DP node
  (Dmitry).
- Expanded the Kaanapali DP node commit message to document USB/DP PHY
  mode switching for DisplayPort altmode (Dmitry).
- Extended the MTP USB headset and Type-C commit message to document the
  WCD9395 USBSS mux I2C bus frequency of 100 kHz (Dmitry, Konrad,
  Mukesh).
- Removed an unnecessary line break from the DP node clock parent list
  (Dmitry).
- Link to v1: https://patch.msgid.link/20261005-kaanapali_dp-v1-0-6faeac3a6d59@xxxxxxxxxxxxxxxx

---
Balaji Kalkonda (5):
      dt-bindings: display/msm: dp-controller: Document Kaanapali
      drm/msm/dp: Add DisplayPort controller for Kaanapali
      arm64: dts: qcom: kaanapali: Add DisplayPort controller
      arm64: dts: qcom: kaanapali-mtp: Enable USB headset and Type-C accessory mode
      arm64: dts: qcom: kaanapali-mtp: Enable DisplayPort over USB

 .../bindings/display/msm/dp-controller.yaml        |  2 +
 .../bindings/display/msm/qcom,kaanapali-mdss.yaml  |  7 ++
 arch/arm64/boot/dts/qcom/kaanapali-mtp.dts         | 61 +++++++++++++++
 arch/arm64/boot/dts/qcom/kaanapali.dtsi            | 90 +++++++++++++++++++++-
 drivers/gpu/drm/msm/dp/dp_display.c                |  6 ++
 5 files changed, 164 insertions(+), 2 deletions(-)
---
base-commit: 9a482184d910775cf648863148944945b74e2815
change-id: 20261005-kaanapali_dp-f6d6839731fb

Best regards,
--  
Balaji Kalkonda <balaji.kalkonda@xxxxxxxxxxxxxxxx>